Voidlings First Cab

So my temps came down to 60.

Put some clones in 3 inch neoprene disks. They come with a large plugs in the middle. Without them clones extremely loose. With it in the stem seems quite pinched.

With 3 teaspoons of maxigrow and some aqua shield got ppm of 550 and pH of 7. Added pH down.

Shitty luck... hopefully better luck this time.

It's all good. Just got to figure out what's going wrong. Unfortunately the suction cups on the pump aren't staying anymore. They did the first grow but not since

I either read my meter wrong last night or my ppm went up by 100.

Rez temp climbed back up. Guess I got to ice it more often. Need a way to secure a bigger ice pack in there without damaging roots.

My mother plant seems to be dying so need to get one of these established. Im assuming root bound. Can't fit a bigger pot in my cab.

The very end of the tips turned white and curled up just a little. All I can find is mag def but it should start that fast should it? The clones left in cloner with no notes don't show the same problem. Could it be reaction to the led? I might have to clone under led rather than cfl.

If mag def then should I use magical or Epsom salt? I'm using hard water.

Recently rooted and moved into nutes two nights ago. Nutes are MaxiGro 10-5-14, 3 teaspoons for 7 gallons, reading 650ppm last night.
3 of the plants I put in the swc


One I put in soil. Is that just veg preflower?


The clone tote. They're showing the same signs after all.


My mother is toast. Either the miracle grow nutes were shit and helped kill clones and mother or the mother got root bound. Now I think about it, the clones in swc didn't get mg so who knows.

Surely you didnt take your cuts from the one in the Corner of this pic?



Beech

They are from that plant, but before it started crapping out. It's either root bound or the mg nutes fried it over time. Or maybe the plant had an issue that showed up in the clones dying before it managed to kill the mother

Ah, I was only using it long enough to clone. Was for a test initially to see if it would work. Now that I know it does I'll dry it off and paint it. What size net pots do you use?

Voidling said:

Ah, I was only using it long enough to clone. Was for a test initially to see if it would work. Now that I know it does I'll dry it off and paint it. What size net pots do you use?

Click to expand...

4"pot 6-8" rooted clone,goes straight to the bottom then fill in with pebbles.
I always pull a few roots thru the bottom of mesh pot,Very gently trying to get the tap hanging.
Guess i could just raise water level,But when i do it splashes from the pump,everywhere!!LOL

Beech

Yeah don't want water coming out. I've debated on going up to 3 inch on the cloner or down to 2 inch on my swc.

I'm wondering if my prior issue was with putting the clones into net pots with roots too long. I just checked them rather than pulled them through

^^^^ Why I don't do hydro

Yeah yeah. My problem is that pots take up too much height in my tiny cab.

Yeah but the plant still has to be sitting in the hydro setup as well that takes height too

Yes but only like half the height of the cartons I was using or my 5 gallon pots

use smaller pots. fuck hydro, its not for you. Plus you don't run enough watts for 5 gallon pots in flower. And i don't see why youd have 5 gallon pots in a cab.

Senseimilla said:

^^^^ Why I don't do hydro

Click to expand...

Ha ha,New run is Organic Soil.

Beech

Nah 5 gallons are my outdoor chili plants. I only have like 3 ft and the light and exhaust takes up a foot or so. The silk milk containers were a bit tall. All the pots I saw seemed tall

I want to give you a solution. But can't think of one. How much sace do you have where it is an issue.