got my bill
- Thread starter mojoganjaman
- Start date
mojoganjaman
Well-Known Member
welp...I'm back...lookin' to source a 40 inch worm drive hose clamp that ships to Canada...any help appreciated..thanks
mojo
mojo
Roger A. Shrubber
Well-Known Member
https://www.amazon.com/Fantastic-Displays-Adjustable-Release-Banding/dp/B01M352MZ3
not sure about shipping to Canada...but 10 bucks is way cheaper than i expected
not sure about shipping to Canada...but 10 bucks is way cheaper than i expected
mojoganjaman
Well-Known Member
how hard are ya lookin tyo hold what ever it is yer planin on holding?
Tie wraps work bu chance?
YOu can make any of those straps adjustable//////plumbers strapping can work as well depending on how hard it has to hold..
Jefferson1977
Well-Known Member
How about this make a clamp system? It's good to 100 feet lol. You can get the 8.5 foot starter kit for 20$.
https://www.globalindustrial.ca/g/plumbing/hoses-and-hose-fittings/hose-clamps/make-a-clamp?trackType=null
https://www.globalindustrial.ca/g/plumbing/hoses-and-hose-fittings/hose-clamps/make-a-clamp?trackType=null
Last edited:
mojoganjaman
Well-Known Member
ok folks....I make no less than 5 gal pails of iso...then the wash gets strained...to strain I use window screen...I always need a third hand to secure the picture hanging wire I use to secure screen..its a pain...with a clamp, I kin put screen on bucket..adjust clamp size...and just slide the clamp over screen and bucket...tightin clamp and strain...just lookin for simple solutions....thanks folks...
mojjo
mojjo
Jefferson1977
Well-Known Member
Seems like the make a clamp is your best bet. 20$ and ships in from Canada. Cut to size.
At the link above i believe you would order this. Then just cut it to size.
Last edited:
Jefferson1977
Well-Known Member
Darn bud I just tried to checkout for ya and they want you to purchase a min. of 7. Oh well.
CannaReview
Well-Known Member
Take two or three clamps and make them into one?
Jefferson1977
Well-Known Member
This one says it is 8.5 feet make a clamp for 20$ on amazon.ca so ships to Canada.
https://www.amazon.ca/Breeze-Clamp-Stainless-System-contains/dp/B0002QTJ0E/ref=sr_1_1?ie=UTF8&qid=1547343256&sr=8-1&keywords=make+a+clamp+8-1/2+band
https://www.amazon.ca/Breeze-Clamp-Stainless-System-contains/dp/B0002QTJ0E/ref=sr_1_1?ie=UTF8&qid=1547343256&sr=8-1&keywords=make+a+clamp+8-1/2+band
you know what yer doin
meangreengrowinmachine
Well-Known Member
could you use a thin ratchet strap in a pinch and cut off the excess?
mojoganjaman
Well-Known Member
meangreengrowinmachine
Well-Known Member
happy to contribute any way I can! I just read the whole thread.... and I hope you kick this shit man! Keep up the good fight!
Farmer.J
Well-Known Member
Couldn't you just buy a roll of haywire and vicegrips? Just tie the wire around the bucket over the screen. Use the vicegrips to twist the ends together until it's tight. Cheap as borsh.
Boatguy
Well-Known Member
Cut out the lid, leaving the perimeter, throw the screen over the bucket loose(for stretch), and put the cover on.
OldMedUser
Well-Known Member
Shorter hose clamps can be joined together to make a longer one as well. 6" ones are $2 each at the local UFA here in BumF**k, AB.
