Victor6634
Well-Known Member
Thank you Stephenj37826
DIY with Quantum Boards
- Thread starter robincnn
- Start date
qballizhere
Well-Known Member
Hell I was thinking of using Elg-240-54-d2 driver in veg and dim when needed
Stephenj37826
Well-Known Member
I have tested B type and it pulls around 170-180 watts at 120 vac. You can't run them in series on that driver. It is only 143 volt. A TYPE will do better.
Stephenj37826
Well-Known Member
Won't work. You have to have 110+ volts. Sorry.
qballizhere
Well-Known Member
ooppss just dabbed meant to say elg 240 2100 d2
REALSTYLES
Well-Known Member
Well here's my light it it has a super clean look
REALSTYLES
Well-Known Member
RuRu.The.Half.Elf
Well-Known Member
What alum angle did you use? 1"x1"x.25"?
REALSTYLES
Well-Known Member
no 3/4" $2.11 for 4' section from Lowes
Edit:My bad it's 1/2" I'm such a stoner lol
Last edited:
Budzbuddha
Well-Known Member
Nice ... It looks like you popped a heineken right after ( bottlecap ) LOL
MMJ Dreaming 99
Well-Known Member
Looks awesome. Post some plant pics when you get going.
nl5xsk1
Well-Known Member
So, is this 24×24? What size room for this unit? Captain Morgan has same setup gor a 3×4
Last edited:
REALSTYLES
Well-Known Member
I don't know lol and my frame is 19"x25" I'll have to grow with it first
nl5xsk1
Well-Known Member
So what is your preference when runnung driver's, A or B, i am currently running 8 3590's and use two drivers so i went with eternal dimmer. Now im getting 4 quantum's with one driver, wouldnt it make sense to simply get an internal?
Budzbuddha
Well-Known Member
robincnn
Well-Known Member
Made a kit for myself.
Last time i assembled in 9 mins.
This time it took longer. Wanted to make sure wires look good. Drilled a hole for + Wire
Removed the sleeve for DC cable
- from driver straight to Board.
+ from driver wired with a Wago and 18 gauge solid core.
Last time i assembled in 9 mins.
This time it took longer. Wanted to make sure wires look good. Drilled a hole for + Wire
Removed the sleeve for DC cable
- from driver straight to Board.
+ from driver wired with a Wago and 18 gauge solid core.
Stephenj37826
Well-Known Member
A type generally will give you more power so i like them better if you have access to the driver.
robincnn
Well-Known Member
2 Boards on a HLG-240-1050A dimmed to 250W
Pics of lamp here. 2nd pic
https://www.instagram.com/northerngrowlights/
Boards wired like this in series
Sensor used here is an old SQ120. Will make new charts in 2-3 weeks with Lighting Passport Spectrometer
12 inches and 18 inches. No optics on boards.
Tent was 2x2.5 and measurement was taken only in 2x2
Pics of lamp here. 2nd pic
https://www.instagram.com/northerngrowlights/
Boards wired like this in series
Sensor used here is an old SQ120. Will make new charts in 2-3 weeks with Lighting Passport Spectrometer
12 inches and 18 inches. No optics on boards.
Tent was 2x2.5 and measurement was taken only in 2x2
MeGaKiLlErMaN
Well-Known Member
what do you have to run to get the same output in a 4x4? at the same heights?