Flower Rosin Man Cave
- Thread starter medidedicated
- Start date
medidedicated
Well-Known Member
medidedicated
Well-Known Member
medidedicated
Well-Known Member
17% of 3.31 is .56gs Im screamin in joy. I didnt lose the pheno. I just cant guarentee a certain amount like guessing yield. No one does but I was close each time. Its just less predictable but damn.
medidedicated
Well-Known Member
medidedicated
Well-Known Member
Damn, yall gonna let a brotha sit in jail alone lol. Where everyone at? Im about done, the last press of course the pre press mold jammed. From being extra hashy, a sweet problem to have. Because the yield is higher.
Attachments
medidedicated
Well-Known Member
Now to collect. 179.11gs pressed and got a test sample drying still thats about 5gs. Just seeing if it was a drying issue but this appears to be doing good. Must be a performance issue that got pretty low on those two clones. Idk what this is yet but the test press is a good clue and was 17%.
Attachments
medidedicated
Well-Known Member
medidedicated
Well-Known Member
medidedicated
Well-Known Member
8.5% of 3.47 is .29gs so yea I aint keepin this. Another hashless pheno.
medidedicated
Well-Known Member
medidedicated
Well-Known Member
Its on. Show time.
medidedicated
Well-Known Member
Pressin. Its gonna be like a 12-14% but I think I know why now. Need to do a reversal hunt and see whats the best I can mother or restart. In theory I should always get similar yields instead of losing 7% for no reason, its for a reason if all else is in check.
Attachments
medidedicated
Well-Known Member
medidedicated
Well-Known Member
Rest of it. 220gs now to collect. Was 233gs altogether with test presses so wow was a 8.35oz clone. A half pound plant. Too bad I lost extract yield in the pheno hopefully I salvage it. Or else fuck it, I might as well pop another watermelon ultra bean. Start fresh.
Attachments
medidedicated
Well-Known Member
Another session all alone. Where everyone at? Ahh takin break before collect. This was a heavy session.
medidedicated
Well-Known Member
What a pain to collect I just was fustrated. 60/60 and better quality but damn do I have to work for it. 233.5gs to 13.4% rosin or 31.28gs.
medidedicated
Well-Known Member
medidedicated
Well-Known Member
Yea its not just looks it is softer and just much lighter. Got that strong og kush aftertaste.
medidedicated
Well-Known Member
So the darker transparent parts of the paper after pressing, where the bud was.. I been calling those areas sinks vs source. You got to leave some behind there sometimes as its a sink, its going to take rosin off your tool rather than collect. This run that was so true, soo many sinks.
You know why, it just grabs rosin off the tool right, then it starts to rip. Now theres paper fibers in the rosin!
So just get the best you can immediately until its like meh just a pinner dab. Then dump into jar and get the rest with the tool clean of rosin. Then try to get it. You can turn flat tool upside down its meant to squeegy the rosin. Then dab that thin sheet of left over rosin by dabbing it.
With this 60/60 quality, it gets so sticky at that point, the paper is just glueing on to tool each dab. It can rip the paper therefor. Man these papers changed their quality too so Im open to parchment paper suggestions.
Its more sleek, I think even dishonest to labeled proportions.. Rips easier. Different texture and shine/transparency.
That squeegy technique Id do when it yields decent like 17% and up. Then go back for the rest later as it vapes off more terps and becomes scrapable/collectable. Its just suddenly a pain but its worth ivesting in as it made quality a lot better.
You know why, it just grabs rosin off the tool right, then it starts to rip. Now theres paper fibers in the rosin!
So just get the best you can immediately until its like meh just a pinner dab. Then dump into jar and get the rest with the tool clean of rosin. Then try to get it. You can turn flat tool upside down its meant to squeegy the rosin. Then dab that thin sheet of left over rosin by dabbing it.
With this 60/60 quality, it gets so sticky at that point, the paper is just glueing on to tool each dab. It can rip the paper therefor. Man these papers changed their quality too so Im open to parchment paper suggestions.
Its more sleek, I think even dishonest to labeled proportions.. Rips easier. Different texture and shine/transparency.
That squeegy technique Id do when it yields decent like 17% and up. Then go back for the rest later as it vapes off more terps and becomes scrapable/collectable. Its just suddenly a pain but its worth ivesting in as it made quality a lot better.
