Ethos Banana Hammock comparative(exodus thread)

Hom3grown0815

Hom3grown0815

Active Member
Moabfighter said:
My ole lady even knows who you are @Soil2Coco

“Talking to my buddy with the severe health issues”


“Soil2coco?”

You got more people thinking about you than you’ll ever know man. Fight hard.
Click to expand...
Moabfighter said:
Big Steve! We are all here!

Fuck. Homegrown. I want homegrown in here. He came to be a really good dude, in my opinion. I know for a fact I gave him The cold shoulder at first but he remained active and persistent. Good grower. Would like for him to compete with us.
Click to expand...
Moabfighter said:
Sent him
Moabfighter said:
Big Steve! We are all here!

Fuck. Homegrown. I want homegrown in here. He came to be a really good dude, in my opinion. I know for a fact I gave him The cold shoulder at first but he remained active and persistent. Good grower. Would like for him to compete with us.
Click to expand...
Made me smile reading that shit. I'm here more or less to watch. Just dont have the funds at the moment to drop on beans. I have plenty of beans I could pop but not ethos. Kill it guys.
Click to expand...
 
Hom3grown0815

Hom3grown0815

Active Member
Smokexbreak said:
Got step one of the new tent set up done.
Using 2x4 of my tent for hempys that I’m hooking to a manifold and reservoir. Gonna make those later tonight or tomorrow depends how long this trim session takes. Probably going to put a couple DWC plants in the front half once my other 96’s get here.
I’ll have 4 96’s total and I’ll Be adding the last two mid summer to make it an even 6.

Any way I’ll be switching the buckets for a tray and then drilling new drain holes to run a 1/2” drain tube from the tubs into the tray/bucket. And the. I’ll be running 1/2” tubes from each halo ring to the manifold then to my reservoir. I’ll be adding on and off valves between my manifold and my Halo rings so I can control the water flow and water all three at once or one at a time.



View attachment 4324074 View attachment 4324075 View attachment 4324074 View attachment 4324076
Click to expand...
You have it looking good man
 
ClydeWalters

ClydeWalters

Well-Known Member
Moabfighter said:
Any good reason not to start seedlings in a tiny cloner aeroponic type setup?

Something about sticking a couple threads thick root into a 5 gallon jet pool of rapidly rolling bubbling water just doesn’t sound ideal to me.

That’s what happens. I seen it. You don’t get a big ole handful of fat roots to start. You get one long string. The tap root. Mine broke about 87 times.
Click to expand...
You should NOT have a turbulent root zone.. if you do you have TOO much air coming out of your stone. Open a valve or two until it’s GENTLY rolling... I mean gently

The results you see me get are with minimal air in my buckets
 
Soil2Coco

Soil2Coco

Well-Known Member
Moabfighter said:
I need someone to help me figure out how to take efficient clones etc. surely there’s ways to take a few and pick better traits to flower. I’d have to imagine. But I’m clueless.


I’d like to get two harvests off these single bean pops if possible. It is possible I mean. Just need a simple how to and some wordy info as to where and why.
Click to expand...
Build a bubble cloner. Pick a container to fit your needs. I have a small square screw bucket with 5 spots on the lid and holds about a gallon of water. I also have about a 16” x 32” tote that’s about 8” tall, and holds 24 clones.

2” net cups with bottoms cut out

Neoprene clone collars.

Enough air stones to get the water rolling. Oxygen is your friend.

Big enough air pump for container. My small container uses one 6” stone, and my large container uses 2 or 3.

Aquarium heater to keep temps around 70

Cut your clones. I like bigger clones with at least 3 nodes. Use razor to cut bottom on a 45. Lightly scrape sides on last inch of stem and place inside clone collar then into net pot then into cloner. Cloner should be filled with water up to bottom of net cups and light bloom nutes added (the high P and K is needed for rooting not just flowering).

This is set it and forget it, roots in 7-14 days

These cooked a little too long but I was sexing these cuts since I’m running regs this cycle. You’ll want to transplant them a lot sooner

580D7D79-0A48-4846-A26A-1D26A2DE1EBF.jpeg
 
Hom3grown0815

Hom3grown0815

Active Member
Soil2Coco said:
Build a bubble cloner. Pick a container to fit your needs. I have a small square screw bucket with 5 spots on the lid and holds about a gallon of water. I also have about a 16” x 32” tote that’s about 8” tall, and holds 24 clones.

2” net cups with bottoms cut out

Neoprene clone collars.

Enough air stones to get the water rolling. Oxygen is your friend.

Big enough air pump for container. My small container uses one 6” stone, and my large container uses 2 or 3.

Aquarium heater to keep temps around 70

Cut your clones. I like bigger clones with at least 3 nodes. Use razor to cut bottom on a 45. Lightly scrape sides on last inch of stem and place inside clone collar then into net pot then into cloner. Cloner should be filled with water up to bottom of net cups and light bloom nutes added (the high P and K is needed for rooting not just flowering).

This is set it and forget it, roots in 7-14 days

These cooked a little too long but I was sexing these cuts since I’m running regs this cycle. You’ll want to transplant them a lot sooner

View attachment 4324126
Click to expand...
I use those exact same net cups and collars For my cloner
 
Moabfighter

Moabfighter

Well-Known Member
bigggsteve89 said:
Always make edibles or ill make hash caps. I got quite a bit of trim im planning to blast then got this stuff called shatter sauce came in a kit to make my own oil to fill a cart and vape cant wait to give it a go!
Click to expand...
I’ve never in my life “vaped” but if you could get this tank filling stuff down let me know. I’d be interested in cutting my stuff down to just lightly smoke on all day.
 
You must log in or register to reply here.
Top