Help! My Patients want wax not bubble Need to make decision now
- Thread starter fluffygrrrl
- Start date
Blunter the kid
Well-Known Member
I would imagine as long as the solvent the extract is made with has no impurities or additives then unpurged wax really it's as dangerous as everyone perceives it to be, but I would still much rather purge my extract because the solvent makes it harsh and sizzle when you smoke it.
I could be wrong but I think at the temperatures a titanium nail reaches any butane inside your dab would decompose into hydrogen and carbon dioxide, I would imagine carbon monoxide could also form.
Last edited:
SlowTwitch
Active Member
I use living organics too. All Jutes and pesticides I use are food grade. When i make bubble I rinse with to and a few drops of peroxide. Kills anything in it.
SlowTwitch
Active Member
Ro not to and nutes not Jutes fucking phone! Sorry . . .
oilmkr420
Active Member
Why go the paper route? Sinster funnels are relatively cheap on ebay. Fritted disc baby under vacuum is where its at.
oilmkr420
Active Member
Why even fuck w a patients health when it should be a loss for the caretaker for neglecting moisture lock in the first place. Eat the loss and for the sake of GP, just toss it. Its way to plentiful to risk potential misinformed or misinterpreted controversial matters. Why risk the reputation or the fact that some people can't risk the introduction of toxins to the system. Weakened immune systems can have serious health risks involved w substandard medication.
Blunter the kid
Well-Known Member
Those filters are glass fiber not paper.
radrolley
Well-Known Member
i only like using wax in edibles. i dislike dabs, way too harsh on the lungs. i dont see inhaling dabs and kids coughing until their face is blue as being very medical at all. it tears the lungs up. you want to get the cleanest butane you can find. bubble hash is okay but i like smoking weed a lot better. you can check out your local head shop or grow shop and see if they sell the glass tubes. put a few unbleached coffee filters on the big end of the glass tube with a metal clamp to hold it securely. find the appropriate tip that fits the butane nozzle into the glass tube the most tight. make sure it's a well ventilated area, i run ducting from my exhaust fans when my lights are off and just blast under it. it sucks all the fumes out. make sure not to smoke anything nearby. that goes for visitors as well. dont be by a pilot light or anything that could ignite it. it can actually be very dangerous but i dont know anyone personally who has been injured from making it. some cops try to say it's like cooking meth but it's not even close. after you blast the wax you want to put it in a vacuum chamber with heat to purge out any impurities that you can. you may have to do some experimenting to get it how you want it. good luck and be safe.
oilmkr420
Active Member
The reason it's compared and treated like meth manufacturing is because of the rise in trends w structural fires here in the west coast about 8 per week. The charges start at 8 years for doing bho. I dislike dabs that are harsh myself. It's due to under purged residuals of solvents. Fully purged stuff doesn't sizzle unless it's a moisture content left from the water portion in ethanol. I don't worry about fires since when done right, can blast right next to a torch or open flame fearlessly. The advantages over using co2 vs any typical soxhlet extraction are obvious and easily noted which is of higher quality. Even blindfolded you would have a preference for the more pleasurable, smoother, sweeter, and completeness of the high are most commonly noted by people running across my path.
oilmkr420
Active Member
The temp we vape at w a Ti nail is hot enough to force combustion from residues. If it weren't going through a water filtration device, you would pretty much be inhaling a mild open flame. Shit smoking a joint saturated in oil is almost to hot to hold in. For that I use a stick of glass as a crutch. Keeps the joint from going out, prevents fat fingers from closing the joint to the point of not allowing the smoke to pass through, and when the joints gone, there is still a grip of oil to smoke from the tube of pyrex reclaim. Residues are acting like a cut to the final product. Diluting it w space more fit for product any ways.