TIPS ON PURGE

D

DGT-420

New Member
Ok, so I got a new pump and chamber and assumed I could just go directly into the chamber with the oil without letting it set out overnight or even an hour. I have been trying to vacuum purge for four days now at temperatures between 85-115 degrees and it's still solid bubbles. It is a very thin layer on a silicone pad, inside the chamber; at least an oz of final product too so this is an emergency!!! Lol.
Is it too late to fix?? Another problem I'm having is that my pumps will not go any deeper than -22.5 hg, or is that a problem??? It is a five gallon chamber and a single stage/3CFM vacuum pump; I also tried my two stage/3CFM pump and it wouldn't get lower than -20 hg...
Thanks for any experienced advice.
 
Sirdabsalot462

Sirdabsalot462

Well-Known Member
DGT-420 said:
Ok, so I got a new pump and chamber and assumed I could just go directly into the chamber with the oil without letting it set out overnight or even an hour. I have been trying to vacuum purge for four days now at temperatures between 85-115 degrees and it's still solid bubbles. It is a very thin layer on a silicone pad, inside the chamber; at least an oz of final product too so this is an emergency!!! Lol.
Is it too late to fix?? Another problem I'm having is that my pumps will not go any deeper than -22.5 hg, or is that a problem??? It is a five gallon chamber and a single stage/3CFM vacuum pump; I also tried my two stage/3CFM pump and it wouldn't get lower than -20 hg...
Thanks for any experienced advice.
Click to expand...
How big is your chamber mang?

Oz O oil in a small chamber, won't work...

How thick is the slab?
Your elevation?
Sea level?

Subtract approximately 1” of Mercury for every thousand feet of elevation.

I'm in Co.Springs my gauge pegs at 22.5

Try taking at least half the oil out and set it aside...

Make the oil in the chamber as thin as possible..

While the oil is molten (soft), lay a sheet of parchment paper over the slab, and sandwich.
Now, grab a riling pin and flatten the slab, making the oil very thin.
You may have to stick the it in the freezer for a moment to remove the parchment...

Try again like that.
 
Last edited:
D

DGT-420

New Member
Sirdabsalot462 said:
How big is your chamber mang?

Oz O oil in a small chamber, won't work...

How thick is the slab?
Your elevation?
Sea level?

Subtract approximately 1” of Mercury for every thousand feet of elevation.

I'm in Co.Springs my gauge pegs at 22.5

Try taking at least half the oil out and set it aside...

Make the oil in the chamber as thin as possible..

While the oil is molten (soft), lay a sheet of parchment paper over the slab, and sandwich.
Now, grab a riling pin and flatten the slab, making the oil very thin.
You may have to stick the it in the freezer for a moment to remove the parchment...

Try again like that.
Click to expand...
 
D

DGT-420

New Member
Five gallon chamber... 7200 ft above sea level. 22.5 is the deepest it will go. I finally got it right and my freakin pump completely filled my chamber with oil. MOTOR OIL!!!
I'm furious right now. How could the pump push motor oil into the chamber??? So that I never do that shit again, ya dig?
 
D

DGT-420

New Member
And yes, I spread it thin across the entire silicone pad on the first run. After four days of a vacuum purge, still getting bubbles and tasting butane. Wtf am I missin?? I've made dozens of good batches in AZ but since I moved to CO I can't get it right.

S. O. S.
 
Sirdabsalot462

Sirdabsalot462

Well-Known Member
You need to have an isolation ball valve between the vac and the port....

Negative pressure inside the chamber, will draw pump oil into your chamber.

Damn bro....
Sorry to say, but that batch is ruined.

3$ ball valve...

Also the chamber should be elevated higher than the pump. Put the pump on the floor and elevate the chamber.

Before you turn the pump off, close the valve. Leave it closed before turning the pump back on also.

It happened due to the physical properties of gravity...hence the valve.

I'm sorry to hear this, my heart just broke for you mang...
 
D

DGT-420

New Member
Ok, last question, I hope. Is it ever too late to put a batch back into a purge. The first batch, which is now on day 5, is a solid, almos waxxy substance and is almost a full zip.

So, Now that I have the right temperature on my stove and figured out the pressure on that chart, can I put the big batch back under the purge and get it fully clean? It still bubbles and tasted like butane. Please tell me it's not a waste.
 
D

DGT-420

New Member
Yo, my man. I wasn't able to get my temp high enough without an electric skillet and now I have a semi-hard wax that still has butane in it. Could I possibly put it in the extractor and rerun it??

If not, is there anything that can be done to fix a large batch of wax that wasn't purged properly??
 
P

playa 69er

Member
Sirdabsalot462 said:
No problem my friend.
He breaks it down really well, and his suggestions and techniques usually will get the consistency you desire.

Keep in mind different strains and the age and quality of the starting material plays the biggest role.

So his specific” recipes” per se, may need some tweaking.

It comes with practice and repetition...
Click to expand...
Sirdabsalot462 said:
No problem my friend.
He breaks it down really well, and his suggestions and techniques usually will get the consistency you desire.

Keep in mind different strains and the age and quality of the starting material plays the biggest role.

So his specific” recipes” per se, may need some tweaking.

It comes with practice and repetition...
Click to expand...
ok fellas first run over,ended up With some shatter..didnt run much,just trying to get a feel for the process before I make bigger runs..but overall happy with the outcome. .just wanted to say thanks to everyone that gave me all the info to make this happen..thanks guys. .
 

Attachments

D

DGT-420

New Member
Does anyone know how to break down the process, step by step, of winterizing for the purpose of getting 100% of the butane out??? I have a batch that isn't clean enough for consumption and it's over an OZ that I need to clean. At 7200ft elevation and its still fairly cool here. IF that matters.
BLESS
 
B

Benplugn

New Member
Hey I see your giving out really good tips the only thing is they still dont work cause I used em ... what's wrong with my skill
 
You must log in or register to reply here.
Top