Ready to clone.

I think I'm ready to clone or at least going to try !! Going to use Dowsers method for cloning with the Jiffypot and all !! My question is : is my plant ready for cloning and also when should I start to flower it ? Here are some pics. Would like to some input !!

Thanks

You should wait until your plant is more mature. The side branches are still growing across from each other. It is not mature yet.

Some people go by the 4 nodes high means good to go method, but I say let her grow some more. Any clones that you take now will be very small.

LEt the plant use all its branches to get some growth on her.

? why is your pics out of date, what time zone are you in.

lmao cause everytime you take the SD card out of it you have to reset the time and year etc ... I stop doing it sometime ago Those pics are with the new 6th gen UFO LED which just came out !!

StreetRider said:

You should wait until your plant is more mature. The side branches are still growing across from each other. It is not mature yet.

Some people go by the 4 nodes high means good to go method, but I say let her grow some more. Any clones that you take now will be very small.

LEt the plant use all its branches to get some growth on her.

Click to expand...

Very good Thats why I asked !! Thanks

Peace ~~~~~~~~~

amrock said:

? why is your pics out of date, what time zone are you in.

Click to expand...

Next time I take pics I will set the time and year !!

Peace ~~~~~~~~~~

thnks for the update, anyway it depends on if your going to flower those plants as they are, if so, i say go ahead and clone. make sure you find the strongest top and do some cloning my friend. But if you want the plant to get alot bigger, then i say wait a while let the plant develope more, good luck.

Its the 12/12 flip you should wait for regarding alternating nodes and preflowers.. You could take clones now if your secondaries are big enough and I do think I see one beauty.. Granted I always took really small clones, most ppl take bigger..

Thanks for the reply guys !! I measured the bottom ones at 4 inchs or just alittle less so I went ahead and took 3 from each plant !! Posted some pics in my journal

https://www.rollitup.org/grow-journals/209745-first-time-grower-indoor-tent.html

I didn't think they were that big..

born2killspam said:

I didn't think they were that big..

Click to expand...

The pods are 2 inchs when expanded and I made a hole in the center then quickly cut the leafs off then dipped it in that root powder then put it in the hole. Sqeezed it together then placed it in the cups. You can see 4 branches are at least 2 inch higher then the pods. The 2 smaller ones are still over 3 inchs .. lol Bad cut on my end. I will take pics tomorrow of the places I cut from and measure a few up as well

Peace

What are pods??

Sorry I think they are called pellets !! Pics below !!

Few more pics !! Jiffypot pellets !!

Anyway just checked on them and they look good so far !! No drooping yet

Well everything was awesome until I turned the heat on and forgot about it .... DoH luckly it appear the clones are fine but I thought they were goners !! Will post pics after When I checked the room temp is was 110. When I looked at them they looked toasted !! 2 bigger plants leafs began to wilt but looks fine now !! Tough plants

Peace ~~~~~~~~~~~~~

Heres some pics of the damage !!

JAPPY said:

Heres some pics of the damage !!

Click to expand...

have a link to the dowser method? Im needing something that is a bit more successful than I have been lately. Went from 95% down to 30% success rate in a matter or a few tries.

Heres a link Considering the heat damage the clones have manage to hang on

https://www.rollitup.org/view.php?pg=faq&cmd=article&id=293

Clone the lower branches, wait for the roots to establish. put them in the pots and u can either veg or go right into flower