light bulb vaporizor

i made a light bulb vap. i hit it. i got really high. there was a taste. i dont know if the weed just tastes really weird cuz im not used to it.i used salt. the bulb is clean. now when i was cleaning the bulb, there was a green hard plastic looking coat inside the rim of the aluminum part. it wouldnt come out. was i supposed to get that little bit of green out or is ok. the smell is organic or it seems like it. kinda smells like over ripe brocolli or somethin

Want to try something VERY different today?

Find a large light bulb. Any bulb will do.






Now get a hack saw, a saw with a metal cutting blade, and cut the end of the bulb off, leaving the threads. Go slow, use long slow strokes, and it will cut easily.



You have to hold the bulb firmly, but do not hold it so tightly that you break it. Just saw the 1/6 to 1/4 inch end off.
You will find inside, a ceramic part, and the element that makes the light. Take a screw driver or needle nosed pliers and empty out the bulb. Squeeze the ceramic part with pliers to break it, adn it will then fall out.Just ream it out. Remove the ceramic and the element. You do leave the metal threads on the outside end.
If you had a FROSTED Bulb, then fill it with two tablespoons of salt, and shake it and shake it, and the salt will remove the frosting.




Now get a bottle cap from a bottle of water, and drill two small holes, 1/4 in diameter, in the bottle cap.



Yea, that is my fat beer belly.



That bottle cap will screw on the end of the bulb perfectly.

Now get about two or three feet lenght of 1/4 inch tube, like you use on your airstones and feeder tubes.
Stick 1/2 inch of the tube in the bottle cap, and glue it or use a pin to fasten it to stay. The other hole is your SHOTGUN hole.




Figure out a way to rest the bottle over a flame, over a candle, or over a hot stove eye. You want to HEAT the bottle, but not burn yourself.
DO NOT TOUCH THE BOTTLE.



DO NOT TOUCH THE BOTTLE.




DO NOT TOUCH THE BOTTLE.



You load a small 1/4 inch ball of pot, the size of an english pea into the bottle, screw the cap on, and rest the bottle over a flame. Within a minute or two, the bottle will fill up with VAPOR, NOT Smoke, but a VAPOR, or like steam. Hit it. Two hits will blow you away, you get more THC and less canabanol. For two mintues, you will think "I didn't get any" but after a few mintues, your head will spin.

badass. will have to try that next time i have enough free time to get bored. too busy lately.

YALL WANT SOME CRACK?!!?!!!?

J\K this is one of my fav ways to smoke hash\kif

people see you smoking out of a lightbulb though and they're like wtf?

if you have a blow torch u can slowly heat up one side. by gently passing the bulb over the flame progressively keeping the flame on the bulb until you can keep it full on without the bulb cracking.. heat up one spot on the side until it gets red or soft and then blow hard and firmly onto the metal in. . you got a blow hole.

dont even have to cut the metal end. hold the bulb upside down in your and. and hit the black part(ceramic part) with the tip of a screw driver multiple times, it will break out into the bulb. then shake the ceramic pieces in the garbage. pull anything else out with needle nose plyers.

to make into bubbler. heat up a bic pen tube about 1 inch from the end until it is soft. then bend th pen at that point to a 90 degree angle. tape around that point a crap load of times until you can fit that end in the light bulb opening with a air tight seal. now make a soda bottle bong... and voila..

sorry used to be a druggie. i don't do drugs anymore. drugs are bad.....way way ok fuck it drugs rock.

lol