LED Build 3x3

Skoal · Apr 5, 2019

My thermal paste is taking forever. And no tracking from amazon. Better not be coming from China.

f series · Apr 5, 2019

You're running strips and you're gonna paste em?

Skoal · Apr 5, 2019

f series said:
You're running strips and you're gonna paste em?

Yes. I’m applyingbpaste under the boards and then screwing them down. The consensus a few pages back was that was a good idea or conductivity and longevity of the strips.

f series · Apr 5, 2019

Sweet balls

sonmanc · Apr 5, 2019

My parts came in today. Picked up aluminum u channel. Will start putting the frame together this weekend

pictures soon to follow

Skoal · Apr 5, 2019

sonmanc said:
My parts came in today. Picked up aluminum u channel. Will start putting the frame together this weekend pictures soon to follow

Have fun. I haven’t done squat. I’m not shre when my paste is coming. And that’s the last piece to my puzzle sadly. I was gonna use the u channel but damn they were a pretty penny. Opted for just the sheet.

f series · Apr 5, 2019

Skoal said:
Have fun. I haven’t done squat. I’m not shre when my paste is coming. And that’s the last piece to my puzzle sadly. I was gonna use the u channel but damn they were a pretty penny. Opted for just the sheet.

Have you tried heatsinkusa? It's like 4 dollars per 25 inch piece

Skoal · Apr 5, 2019

f series said:
Have you tried heatsinkusa? It's like 4 dollars per 25 inch piece

I got my sheet already. My boards have been mounted. And holes drilled waiting on my thermal paste to put under the strips before I fire em up.

sonmanc · Apr 5, 2019

I got 30 feet of 3/4 inch u channel and 8 ft angle for like 50. from metals r us. Mainly for support. it will transfer some heat as well.

Skoal · Apr 6, 2019

Still waiting for my paste. But I installed the hanging wire. And this is how she’s going to hang. Will be using two ratchet straps to hold from each hanging point where my fingers are. Coming along nicely.

sonmanc · Apr 27, 2019

Light is finished, just need to wait for a few dabs of silicone to dry that is sealing up the boxes and open solder pads. Clones go in tomorrow! Very exciting. Pics showing it running 9 lights. I have a switch on top that shuts off 6 lights for seedling. The switch box also contains all the wireing ends all nice and hidden away. All wires that run close to other wires or grounded frames all have additional covers. To protect from any potential voltage leakage risk. Rather than extending the power cable I just added a plug end and added a gfci box directly on the device so I have an extra outlet and a bit of extra protection and this forces the gfci to go with it.

Skoal · Apr 27, 2019

sonmanc said:
Light is finished, just need to wait for a few dabs of silicone to dry that is sealing up the boxes and open solder pads. Clones go in tomorrow! Very exciting. Pics showing it running 9 lights. I have a switch on top that shuts off 6 lights for seedling. The switch box also contains all the wireing ends all nice and hidden away. All wires that run close to other wires or grounded frames all have additional covers. To protect from any potential voltage leakage risk. Rather than extending the power cable I just added a plug end and added a gfci box directly on the device so I have an extra outlet and a bit of extra protection and this forces the gfci to go with it.

Looking good bro! I’m still waiting on my thermal paste. Apparently it’s been lost in the mail. I’m itching to get mine up and running. It’s literally just waiting for the paste.

sonmanc · Apr 27, 2019

Thanks, yeah waiting for paste is a good idea, the tape don't hold that well. I had to use silicone around the heatsync edge to keep it from lifting. Even cleaned the strips and aluminum before installing.

1212ham · Apr 28, 2019

I haven't had trouble with the tape, can you link the tape that you used?

sonmanc · Apr 29, 2019

https://www.amazon.ca/gp/product/B07BHK2Z1Y/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 . This tape

Skoal · Apr 29, 2019

sonmanc said:
https://www.amazon.ca/gp/product/B07BHK2Z1Y/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 . This tape

I was going to use that tape. Instead I went hvac screws to secure the strips and thermal paste under the strips.

sonmanc · May 3, 2019

I'm supprised how much the tent heats up with the light. Had to duct the room out to drop the temp of the room, when running 9 lights the tent goes up to 25-26. All 15 it goes up to 30-31 which is too much. Fan blower is cranked as well.

Skoal · May 24, 2019

My paste that I ordered that someone recommended off amazon never showed. 2 months later. Buddy took my money and ran. Finally got my money back from amazon.

I ordered 40g of silicone thermal paste directly from amazon. Not a third party seller. Well ordered on Wednesday. Came today. All and all I will be taking the strips off the aluminium sheet. Placing the paste on the strips and re screwing my strips down. All and all this weekend imma be a go and start flowering. Thank god!

Skoal · May 29, 2019

Shot of the light up and running. Damn the driver gets pretty warm. Warmer than my ballast on my MH. https://instagram.com/p/Bx-S7ZBB8mR/

sonmanc · May 30, 2019

Yeah my tent is hotter now with this lite, some times it gets up to 29 degrees. Plants love it tho. Here is my current grow at 10 days into flower I did end up vending the exhaust to the house return air, it keeps the room down a few degrees

LED Build 3x3

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Member

Well-Known Member

Well-Known Member

Well-Known Member

Member

Well-Known Member

Member

Attachments

Well-Known Member

Member

Well-Known Member

Member

Well-Known Member

Member

Well-Known Member

Well-Known Member

Member

Attachments