OhNo555
Well-Known Member
First we will break it down into phases. This seems easiest as you can refer back to any point of the cure by phase. Try to think of it like landing an airplane...
Phase one: The dry. This is kind of like preparing to land. The first thing you want to do is come to altitude and lower your landing gear. Basically, once you cut your bud, you need to decide what to do with it. Most of us go ahead and trim it now. Once it is trimmed to our liking, the bud is hung to dry.
Phase two: The pre-cure. This is somewhat like landing your airplane. The trick is to set it down on the runway at just the right angle as you begin to reduce your speed. This is where the mathematics come into play. What you are looking for here is the "feel". When your hanging bud begins to "feel" like it is drying out, but the stems are still flexible, it is time to jar. Don't worry, we will revisit this phase in more detail in a bit..
Phase three: The cure. Now your airplane is on the runway. This is where you are focusing on your instruments and applying the brakes. This is the actual part of the cure. It is a benefit to keep your bud in this stage for as long as possible. Actually, this may be a little misleading as some folks may like some cures better than others. In other words, this is the point where smells and flavors can change drastically. Depending on what it is you are after will dictate exactly how long you keep this phase in check. But only you can decide what you like.
Phase four: Storage. Well, the flight is over, time to put the airplane away. We have finally reached a point where the curing process has greatly slowed down and it is safe to store your bud.
Hygrometer is needed.
Phase one. 70% RH: This starts out just like any other time you have done it. Once you have harvested your bud and trimmed it to your liking, hang it in a cool dark place. This is where we will part from tradition. Allow it to hang until the buds begin to feel like they are drying (note the temps and rh as this will rarely be the same during subsequent harvests). They will start to lose their "softness" in favor of a slightly crispy texture. We don't want to allow it to dry until the stems snap. THIS IS WRONG! We want the stems to be flexible. Not totally soft, but not snapping, either. If allowed to dry until the stems snap we risk it drying too much and losing an opportunity to take full advantage of the cure window. You see once the bud reaches the 55% RH range, the cure is dead. No amount of moisture added will revive this. If you are a brown bag dryer you can still use this technique, although I no longer do. I feel it is unneccessary at this point in the drying process. Just make sure you do not over dry. Also, this is a perfect time to calibrate your hygrometers with your new calibrating kit. This phase may take anywhere from 2 to 7 days depending on ambient temp, RH and strain, etc. It is important to be right on top of this phase. Sometimes we will notice thinner stemmed buds getting done quicker. It is ok to take these first and put them in the jar. Just screw the cap on very loosely until the bulk of the bud joins it.
Phase one: The dry. This is kind of like preparing to land. The first thing you want to do is come to altitude and lower your landing gear. Basically, once you cut your bud, you need to decide what to do with it. Most of us go ahead and trim it now. Once it is trimmed to our liking, the bud is hung to dry.
Phase two: The pre-cure. This is somewhat like landing your airplane. The trick is to set it down on the runway at just the right angle as you begin to reduce your speed. This is where the mathematics come into play. What you are looking for here is the "feel". When your hanging bud begins to "feel" like it is drying out, but the stems are still flexible, it is time to jar. Don't worry, we will revisit this phase in more detail in a bit..
Phase three: The cure. Now your airplane is on the runway. This is where you are focusing on your instruments and applying the brakes. This is the actual part of the cure. It is a benefit to keep your bud in this stage for as long as possible. Actually, this may be a little misleading as some folks may like some cures better than others. In other words, this is the point where smells and flavors can change drastically. Depending on what it is you are after will dictate exactly how long you keep this phase in check. But only you can decide what you like.
Phase four: Storage. Well, the flight is over, time to put the airplane away. We have finally reached a point where the curing process has greatly slowed down and it is safe to store your bud.
Hygrometer is needed.
Phase one. 70% RH: This starts out just like any other time you have done it. Once you have harvested your bud and trimmed it to your liking, hang it in a cool dark place. This is where we will part from tradition. Allow it to hang until the buds begin to feel like they are drying (note the temps and rh as this will rarely be the same during subsequent harvests). They will start to lose their "softness" in favor of a slightly crispy texture. We don't want to allow it to dry until the stems snap. THIS IS WRONG! We want the stems to be flexible. Not totally soft, but not snapping, either. If allowed to dry until the stems snap we risk it drying too much and losing an opportunity to take full advantage of the cure window. You see once the bud reaches the 55% RH range, the cure is dead. No amount of moisture added will revive this. If you are a brown bag dryer you can still use this technique, although I no longer do. I feel it is unneccessary at this point in the drying process. Just make sure you do not over dry. Also, this is a perfect time to calibrate your hygrometers with your new calibrating kit. This phase may take anywhere from 2 to 7 days depending on ambient temp, RH and strain, etc. It is important to be right on top of this phase. Sometimes we will notice thinner stemmed buds getting done quicker. It is ok to take these first and put them in the jar. Just screw the cap on very loosely until the bulk of the bud joins it.
