tidywhite
New Member
Greetings All!
Long time looker first time poster, i finally decided to become self sufficient and started with some bag seed to curb some major excitement for my decision. I will be ordering good seeds soon=D
Have a questions about my ventilation system and would like some feedback
Im in the midst of setting up my room, here is a nutshell
8 ft long
4ft deep
6.5 ft tall
partitioned into two 4x4 areas with a divider in the middle. flower and veg respectively.
Im also in the midst of getting my gear in order so i will be ready to start the new seeds, it will consist of 1000w hps, drip feeders in rockwall cubes, GH. maybe an arduino but thats waay down the road.. a bit.
Vegging and cloning will be using an array of CFL, floros, and/or maaaybe a 400 or 600 w MH but thats a big maybe still.
The reason for my post is to find suggestions and opinions to a placement of a certain fan, other suggestions are also welcome!
The pic is the layout of my room with descriptions of what each item is. Im an amateur mspainter
My question is placement on an inline duct booster on the 8" exhaust duct. Lamp and veg room exhaust will feed into this 8" duct at the ceiling. It will be cramped there. The other end of the duct runs to a spare bedroom.
Im hoping to be able to place this fan at or near the end of the duct run, but would like some feedback. Thanks everyone!
A) 25' 8" Duct with 90 degree elbow to enter the room from attic
vents heat from lights and veg room to another room with another 90 elbow to enter that room
b) 4" duct exhausting light heat to the 8" duct
purple circle is squirrel fan
C) 4" duct
venting veg room up the 8" duct
oval is a duct fan
D) 4" duct for room ventilation
exhausting out the carbon filter
green oval is duct fan
E) carbon filter
the exhaust hole on the room wall is at the top right, not left like in picture, oops
F) 1000w HPS
G) lamp intake intake, starts at floor for cooler air
H) 4" intake, pvc or ducting
raised, hopefully keeps co2 from falling out intake hole if were located on the bottom
I) 4" intake, raised
Long time looker first time poster, i finally decided to become self sufficient and started with some bag seed to curb some major excitement for my decision. I will be ordering good seeds soon=D
Have a questions about my ventilation system and would like some feedback
Im in the midst of setting up my room, here is a nutshell
8 ft long
4ft deep
6.5 ft tall
partitioned into two 4x4 areas with a divider in the middle. flower and veg respectively.
Im also in the midst of getting my gear in order so i will be ready to start the new seeds, it will consist of 1000w hps, drip feeders in rockwall cubes, GH. maybe an arduino but thats waay down the road.. a bit.
Vegging and cloning will be using an array of CFL, floros, and/or maaaybe a 400 or 600 w MH but thats a big maybe still.
The reason for my post is to find suggestions and opinions to a placement of a certain fan, other suggestions are also welcome!
The pic is the layout of my room with descriptions of what each item is. Im an amateur mspainter
My question is placement on an inline duct booster on the 8" exhaust duct. Lamp and veg room exhaust will feed into this 8" duct at the ceiling. It will be cramped there. The other end of the duct runs to a spare bedroom.
Im hoping to be able to place this fan at or near the end of the duct run, but would like some feedback. Thanks everyone!
A) 25' 8" Duct with 90 degree elbow to enter the room from attic
vents heat from lights and veg room to another room with another 90 elbow to enter that room
b) 4" duct exhausting light heat to the 8" duct
purple circle is squirrel fan
C) 4" duct
venting veg room up the 8" duct
oval is a duct fan
D) 4" duct for room ventilation
exhausting out the carbon filter
green oval is duct fan
E) carbon filter
the exhaust hole on the room wall is at the top right, not left like in picture, oops
F) 1000w HPS
G) lamp intake intake, starts at floor for cooler air
H) 4" intake, pvc or ducting
raised, hopefully keeps co2 from falling out intake hole if were located on the bottom
I) 4" intake, raised