budbro18
Well-Known Member
hahaha damn!!! Check out domeless.com
http://www.domeless.com/products/product-details/#cid=621466
$75 is so cheap for an enail!!!
DIY E-Nail
- Thread starter budbro18
- Start date
http://www.domeless.com/products/product-details/#cid=621466
$75 is so cheap for an enail!!!
WarMachine
Well-Known Member
The problem with all the cheaper ones that are $100-$150 they are one setting heat and tend to be on the lower end of the scale. The one you listed goes to 6xx mine is adjustable lol. I was going to get that one you listed until the temp was to low, $75 is a steal. Mine was only $15
I'm not saying mines the best or anything, just saying it works lol.
WarMachine
Well-Known Member
I would love to know how the one that domeless listed was made. It seems so simple and obviously low priced so must be low cost to build. Maybe I would be able to kick it up in heat.
PorterRockwell
Well-Known Member
PIMP I want one
Fadedawg
Well-Known Member
Hee, hee, hee............Old engineering proverb WM. If it works, it isn't stupid.
We whomped up this out of thangs lying around, except for the Oil coil, just to try it out, and always planned to eventually design and build something more main stream, but we stay pretty busy and never got any further than figuring out how to easily use it in a circle. Now that we figured out that secret, we will just make ourselves a purdier stand, so we can give Pete his pin vice back.
The nail is an original KO domeless nail, which was donated for testing a couple three years ago, sitting on an original Skunk Pharm dab pipe. Our newer V-2 KO domeless nail is too large for the coil and has a belled entrance.
We just set the coil over the nail and leave it there until we are ready to use it, and then lift the coil off and pass the pipe with no cord attached. When it returns, we set the coil over it again, which rapidly brings it back up to temperature.
Controls are a Mypin PID and a Fotek SSR, in a scrounged box.
Lazy, yes, stupid, not thinking so.
We like it better than one on a cord.
Attachments
Last edited:
torturekiller420
Well-Known Member
You guys can make analog enails fairly simply. Power cord, Light dimmer, and a coil plug. Im pretty sure there is a Tutorial around here or reddit, its simple....really simple.
WarMachine
Well-Known Member
http://www.reddit.com/r/StonerEngineering/comments/29hvq5/as_promised_30_diy_enail_build_instructions_v1/PIMP I want one
That's the guide I used to make it! Pretty straight forward!
WarMachine
Well-Known Member
http://www.reddit.com/r/enail/comments/268n3d/diy_analog_enail_howto/
Very tempting to do lol. Perhaps I will make one or a few..
Very tempting to do lol. Perhaps I will make one or a few..
budbro18
Well-Known Member
I was just about to post this one!
If not domeless has another called the dab pad JR. that can be cranked up pretty high i think its only like $150 ish. But hell for that you might as well build your own. cheap pid/ssr, 14 awg wire, box, coil, done. $100 bucks or less if you look for the deals.
torturekiller420
Well-Known Member
14awg wire? I thought 16awg was to thick so people were using 18awg? Im going to order a wire spool kit(desired wire size in different colored spools). I would hate to order the wrong stuff.
WarMachine
Well-Known Member
Are you guys paying $60-$80 for the coil as well?
jbigdawg79
Well-Known Member
Ok guys a have a xmt-7100 controller I have everything wired and connected. I have power to the unit my coil is not heating up. Is there setting on the temp controller that you have to set up before your cool heats up? If so how do I set up the settings?
jbigdawg79
Well-Known Member
Hellllp Lolololol God it sucks having everything here to use it and don't know how to set up the pid lol sucksssss
Fadedawg
Well-Known Member
Not familiar with that PID controller, but you sound lonely and in need of a dab from your nail.
Did the PID controller come with an instruction sheet written by someone whose native language is English?
You will need to set the temperature that you want it to heat the coil to. Have you done that?
If you have, is the red led on the face indicating that the controller is calling for heat lit? The destruction sheet should tell you which light it is.
torturekiller420
Well-Known Member
Isn't the xmt7100 the same as Aubers 1/32?
jbigdawg79
Well-Known Member
Yes it is
jbigdawg79
Well-Known Member
Cmon my fellow smokers the more I play with it the more I feel like I'm messing it up more. Lol just wanna take a dab again without lighting my dam torch!!! Lol