JB's cheapo diy large capacity ultrasonic humidifier

JSB99

Well-Known Member
I've built a few of these in the past as an alternative to store bought ultrasonic humidifiers. Even the smallest capacity models are around $35 - $50, but you can build your own, for way less, and with larger capacity reservoirs than most of them.

For those who aren't familiar with ultrasonic humidifiers, aka "ultrasonic foggers", "nebulizers", "atomizers" or "cool-mist humidifiers", they are a great way to add humidity to a grow, without adding heat. I'm not going to go into how they work. There's plenty of info out there. I just want to show an alternative method. There are other tutorials out there, but I don't recall seeing one set up like this. So here we go...

This is what it looks like
20180109_132442-1761x1748.jpg


20180109_132513-1274x1787.jpg

Parts:. Nebulizer w/power supply (Amazon, $12), tall, thick plastic cup, pet water bowl with reservoir (this one's 2.5-gallons, but they go up to 5-gallons), and a small aquarium pump. The pet water bowl is the perfect depth for the nebulizer to create fog, and will last a really long time. The nebulizer creates a lot of water droplets that will get everything wet, so the tall cup contains any spray. The aquarium pump is to jet the fog out of the cup. The very smallest will do. You can also use a fan and draw the fog out. Either would probably do fine.
20180109_132547-1834x1683.jpg

Pic of the nebulizer. Using these instead of store bought humidifiers allows you to replace the discs for real cheap, or even the entire nebulizer for as little as $6.99! It's way less expensive than having to buy a new ultrasonic humidifier!

20180109_132619-1743x1283.jpg

Drill a 1/4" hole a couple inches below the rim, then cut the cup from the rim to the hole. This is to hold the power cord, and the nebulizer in place. You want to use a thick cup so it's less prone to cracking, and it helps weigh it down in the water.
20180109_132702-1536x2000.jpg

Drill three more holes around the cup, but this time, only an inch from the rim. These holes allow the water to get to the nebulizer.
20180109_132805-1210x1478.jpg

Next, drill small holes towards the base of the cup. These are where the fog will jet from. You can drill them around the entire cup, or on one side, like mine, to jet the fog in a single direction. Experiment, and see what works best for you. These holes should be much smaller than the previous holes though, otherwise droplets will spray out and you'll end up with a wet mess. I used a 9/64" bit for these.

Also drill a 1/4" hole in the center for the air line.

20180109_132837-1604x1929.jpg


Thread the nebulizer cord through the hole. You don't need to give the nebulizer cord any slack on the inside. As long as the nebulizer is upright.
20180109_132901-1879x1362.jpg


Now just put the air line into the hole, and plug everything in.
20180109_132934-2115x1654.jpg

Use the air limiter to adjust the amount of fog. If your pump didn't come with one, your local hydro store should have them for a quarter or so.
20180109_133002-1264x1145.jpg





 
Last edited:

Tyleb173rd

Well-Known Member
I’ve been looking at these to increase my humidity in my 5x5 grow tent. The humidifier I have now isn’t doing the trick.
 

JSB99

Well-Known Member
I’ve been looking at these to increase my humidity in my 5x5 grow tent. The humidifier I have now isn’t doing the trick.
These work great! There are larger nebulizers, and multi-disc nebulizers available as well. I can raise the humidity in my 2x4x9 mother's closet, 30% or more, and I saw immediate results in my plants. They also help drop the temps a little too.
 

Chrisz0825

Active Member

Cold$moke

Well-Known Member
Siick nice work jsb99

Whats the heat mats do? Besides heat duh but what does it help with?

This is cool cause im making a crazy little hybrid system

And was thinking how i could incorporate a nebulizer as a root fogger.
 

JSB99

Well-Known Member
Siick nice work jsb99

Whats the heat mats do? Besides heat duh but what does it help with?

This is cool cause im making a crazy little hybrid system

And was thinking how i could incorporate a nebulizer as a root fogger.
The mat isn't actually doing anything. It was just sitting there, but I've removed it since, to avoid confusion :)
 

JSB99

Well-Known Member
And was thinking how i could incorporate a nebulizer as a root fogger.
BTW, if you're going to grow via fogponics, you have to use special nebulizers. The ceramic discs that these use will immediately crud up and stop working from salt buildup, from the nutes. But, I'm pretty sure the concept of "fogponics" has been abandoned. Apparently, the ultrasonic vibrations break down and destroy the microbes, and the plant starves. You can use them in cloners though. I've seen pics of really fine hairs developing from taproots, with fogponics. I'd be interested to see how well they work with rooting clones.
 

JSB99

Well-Known Member
Just to let everyone know, the nebulizer used in my fogger has LED lights. I didn't order the one with the lights for any reason at all. It was just a cheap one I found. However, you can get them without the lights. I don't run my fogger during lights-out, so the lights don't interfere at all. It actually looks kind of cool with the LEDs, even though they don't show through the cup much.

Nebulizer without LEDs
 
Last edited:

Cold$moke

Well-Known Member
BTW, if you're going to grow via fogponics, you have to use special nebulizers. The ceramic discs that these use will immediately crud up and stop working from salt buildup, from the nutes. But, I'm pretty sure the concept of "fogponics" has been abandoned. Apparently, the ultrasonic vibrations break down and destroy the microbes, and the plant starves. You can use them in cloners though. I've seen pics of really fine hairs developing from taproots, with fogponics. I'd be interested to see how well they work with rooting clones.
Thanks for the heads up.

Yea the fog was just a add on to what im building just didnt want to buy the expesive fog unit lol
 
Top