Need Help

rick_ca

Member
Hello all don’t know what’s going on lost 4 last one turning yellow I’m following “dyna grow” instruction for a 5 gallon holding tank, light is a 300watt full spectrum led. The feed cycle is 15mins every six hours plant is in a Rockwool starter cube inside a Rockwool 4in cube surrounded in clay pebbles, there is a bubbler in tank and ph. is 5.7 to 6.0. Also the light is 22in from top of the bucket, I did have a 1000watt Hid (MH) lamp but heat in room was too high with it on.
20160730_110652.jpg
 

Airwalker16

Well-Known Member
Hello all don’t know what’s going on lost 4 last one turning yellow I’m following “dyna grow” instruction for a 5 gallon holding tank, light is a 300watt full spectrum led. The feed cycle is 15mins every six hours plant is in a Rockwool starter cube inside a Rockwool 4in cube surrounded in clay pebbles, there is a bubbler in tank and ph. is 5.7 to 6.0. Also the light is 22in from top of the bucket, I did have a 1000watt Hid (MH) lamp but heat in room was too high with it on.
View attachment 3745275
Over watering. Water one 15 min cycle every day or possibly even every other day
 

rick_ca

Member
ok think im loosing the final plant put timer on for 5 mins per day check tds,ph etc mixed nutrients as per dyna grow label, now some leaves are turning brown and curling this is my 1st attempt at hydroponics. Might open tent as air temp was 83 today that with exhaust at full speed ???
 

rick_ca

Member
Dumped the bucket and refilled (well water) took ph from 6.6 to 5.9 added the dyna grow as per label took a ppm reading of 103 X 10 (1030) been looking around local store for a N infussion only thing I can find is a water soluble blood meal im not sure what else to do 1st time with hydro setup
 

ILM

Well-Known Member
Bro you fried them ppm is way too high she looks to young to feeding that heavy . I'm in third wee of flower and I'm only feeding900ppm
I'd scarp it and start over. just my 0.02
 

Boomhour

New Member
For a plant that size you only need an ec of 0.3 or so. I'm not familiar with your setup, but in DWC I add the nutes slowly...over a couple of days....built up to my target ec. watch the plant for changes after you feed it. This feeding schedule might help you out with where your ppms should be in a given week.

http://cch2o.com/feeding-schedule/
 

rick_ca

Member
Thanks for all your help guys fried the last one as ILM posted so here's a question when I do a tds reading here is what I get with plain well water I get a ph 6.6 and a tds 542ppm, is there something I I need to do about this already spent enough on the setup and wife aint to pleased with me LOL. Also I know its early August and I only have about 3 months before the weather drops here in Canada is there a recomendation for a growth/strain using it mostly for joint pains.
 

rick_ca

Member
Boom i need to try talk wife into adding RO system for drinking purposes LOL, but untill then any other surgestion as I cannot find a local supplier of RO water
 

Boomhour

New Member
You could use distilled water from the grocery store. but you will have to add cal-mag because distilled water has 0 base minerals. Add the cal-mag to the water first at 25 - 50% of the recommended low does and then add the other nutrients at the same 25-50% ratio for you seedling. You can slowly raise the amount after you see your plants are consuming the nutrients at a regular rate. I change my water out about every 10 days with fresh nutrients. check and chart your activities everyday. This helps you to keep track of feeding, water changes, days in the cycle, ph, temp etc... This has worked for me.
 

powerslide

Well-Known Member
until you can get an RO about the only way is distilled. Try to add just 100-200 above tap for when they are that small.
 
Top