This homemade smoke buddy will remove all smoke from your toke and leave your hit coming out smelling like air.
What you can use it for:
• Burning in Hotel or Motel
• Burning in Residence
• Burning at relatives house
• Burning at friends house
• Ripping a quick bowl in a public bathroom
What you will need:
• 1 AquaClear Activated Carbon Filter Insert (any carbon filter pouch will do, from any pet store)
• 3 Bounce sheets
• Toilet Paper
• 2 Toilet Paper Tubes
• Tape
Optional but I like better:
• Empty gift card or thick cardboard material to act as end cap
Instructions:
Step 1: To start off you are going to take two toilet paper tubes and connect together. When doing this you may need to dent in one of the tubes so it fits properly, slide the one tube in about 1 inch or so or until held firm.
Step 2: (skip to step 3 if you do not want an end cap) I prefer to have a secured end cap on the end of my tube, the reason is that it keeps everything in place, and nothing will fall out of the one end when you are blowing through it. To make an end cap, I used a plastic gift card that I took from a Tim Horton’s, traced the toilet paper tube onto the card and then cut it out. From there I then took a single hole punch (you can also use a knife in a screw motion) and punched a series of holes into the card like the picture shown. I then used pieces of tape like shown in the picture and folded then over the edge of the tube to hold it tight. To make it a tight seal I put tape all the way around the edges.
Step 3: Now you are going to begin putting the materials inside of the tube. I highly doubt that it matters what order you put all of this in, but for the sake of this tutorial I will explain the order I did it in. To start I put 1 dryer sheet at the very bottom of the tube, to cover up all of the holes we had just made.
Step 4: I then took the activated carbon Insert and wrapped a dryer sheet around it (not completely necessary, but I did it so no smoke gets by the sides) and piece of string to tie the dryer sheet around the activated carbon insert. I then put the carbon insert into the tube and pushed it all the way down to the bottom.
Step 5: You are now going to make a ball of toilet paper, enough to fill almost the rest of the tube, leaving about an inch at the end so your mouth has room.
You have now created a Smoke Buddy for under $5, although it won’t last as long, the only thing that you will really need to change is the toilet paper every couple days.
This homemade Smoke Buddy will filter all smoke out of the air, leaving behind a very faint smell of dryer sheets, unlike a regular spoof where the whole room smells for a very long time afterwards of dryer sheets.
Happy smoking everyone and enjoy your new homemade smoke buddy!
What you can use it for:
• Burning in Hotel or Motel
• Burning in Residence
• Burning at relatives house
• Burning at friends house
• Ripping a quick bowl in a public bathroom
What you will need:
• 1 AquaClear Activated Carbon Filter Insert (any carbon filter pouch will do, from any pet store)
• 3 Bounce sheets
• Toilet Paper
• 2 Toilet Paper Tubes
• Tape
Optional but I like better:
• Empty gift card or thick cardboard material to act as end cap
Instructions:
Step 1: To start off you are going to take two toilet paper tubes and connect together. When doing this you may need to dent in one of the tubes so it fits properly, slide the one tube in about 1 inch or so or until held firm.
Step 2: (skip to step 3 if you do not want an end cap) I prefer to have a secured end cap on the end of my tube, the reason is that it keeps everything in place, and nothing will fall out of the one end when you are blowing through it. To make an end cap, I used a plastic gift card that I took from a Tim Horton’s, traced the toilet paper tube onto the card and then cut it out. From there I then took a single hole punch (you can also use a knife in a screw motion) and punched a series of holes into the card like the picture shown. I then used pieces of tape like shown in the picture and folded then over the edge of the tube to hold it tight. To make it a tight seal I put tape all the way around the edges.
Step 3: Now you are going to begin putting the materials inside of the tube. I highly doubt that it matters what order you put all of this in, but for the sake of this tutorial I will explain the order I did it in. To start I put 1 dryer sheet at the very bottom of the tube, to cover up all of the holes we had just made.
Step 4: I then took the activated carbon Insert and wrapped a dryer sheet around it (not completely necessary, but I did it so no smoke gets by the sides) and piece of string to tie the dryer sheet around the activated carbon insert. I then put the carbon insert into the tube and pushed it all the way down to the bottom.
Step 5: You are now going to make a ball of toilet paper, enough to fill almost the rest of the tube, leaving about an inch at the end so your mouth has room.
You have now created a Smoke Buddy for under $5, although it won’t last as long, the only thing that you will really need to change is the toilet paper every couple days.
This homemade Smoke Buddy will filter all smoke out of the air, leaving behind a very faint smell of dryer sheets, unlike a regular spoof where the whole room smells for a very long time afterwards of dryer sheets.
Happy smoking everyone and enjoy your new homemade smoke buddy!
