Harvest a Pound Every Three Weeks!

dirrtyd

dirrtyd

Well-Known Member
Smokedogg76 said:
I'm almost finished building this hydro/aero setup. Is it possible to clone and veg in the same area, say 25 sq. ft? Also, Could I use 2 400w MH on an 18/6 light cycle? I would really appreciate some help with this one.:wall:
Click to expand...
That's alot of light just for the clone and Veg area. Ihave mine right next too each other and only use five shop lights with 23wt bulbs. I would try one and keep it high for now and then lower you will probably get some stretch. Good Luck
 
B

beer.me

Member
Philo2 said:
Hey do you think these spray jets will clog? The red ones are supposed to be the good ones right?

http://cgi.ebay.com/EZ-Clone-Mister-Spray-Jet-360-Degree-Pack-of-50_W0QQitemZ320447363064QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item4a9c26b7f8

I've been using the ones they sell at my local grow store for my cloner but they keep clogging up on me and they are $1 buck a piece.
Click to expand...
Yes, those are the EZ Clone spray jets that are recommended by Stinkbud. I am using the same ones in my setup and I have had no clogging issues. They look to be a good deal as well.
 
S

slh puffer

Member
i want to do the same but building with a strongbox but 28misters for 14sites instead with a 633gph pump also when building the veg unit do you use any kind of tubing to stop water from leaking between the two boxes from the opening in the center that connects the pump on the bottom(bottom box) onto the misters on top(top box)????If so what material d you use and where an i get them from??
 
dakin3d

dakin3d

Well-Known Member
StinkBud said:
I've never tried Bloom Booster.

Adding Sweet has enhanced the flavor and aroma of my buds. I'm very happy with the results.
Click to expand...
Whats up, Stink? Gotta say thanks for all of the niiice info, plans, etc. I'm sure takes a lot of time to do all of that, and I and others appreciate it greatly. I'm preparing to take the next step and move over from soil.

I have a quick question regarding Sweet. I use the Bot. Pro line, as well as Nirvana, Calmag, etc. What breaks down the complex carbs contained in Sweet, in your nutrient recipe? Does the ProGrow have beneficials in it that get the job done? If so, I wasn't even aware and thought I was going to have to start adding subculture.... Thanks in advance
 
S

sherriberry

New Member
where are you guys getting these 1 min on, 5 min off timers, and whats the best deal on them?

I just built a 56 sprayer veg table for my plants coming out of the sprayer cloner similar to stink's which uses 8 sprayers in the rubbermade tub.

it has a 550gph pump, and sprays plenty still with 56 sprayers...

so i dont think you need that big of a pump to work these things properly.

IM going to buy a 100gph pump, and see if it will power another 8 sprayer cloning tub... i think it will.
 
H

hawaiiankush

Member
Stinkbud,

I finally got throught page 130 and decided I am ready to start the build. One question: Should I add 1/2" and 1" to all measurements before cutting? The plans do not account for the 1/2" telescoping when attaching each part.

For example; when building the veg unit "H," it specifies 7-7" pieces, but in the schematics it measures 7" between the "T's." I can either re-cut and allow for the extra 2" on each side (thus cutting 8" pieces to account for the 1/2" on the endcap and 1/2" for the "T") or drill holes 3" apart rather than 3 1/2." Does any of this matter? Thanks again to all for your help.
 
dirrtyd

dirrtyd

Well-Known Member
hawaiiankush said:
Stinkbud,

I finally got throught page 130 and decided I am ready to start the build. One question: Should I add 1/2" and 1" to all measurements before cutting? The plans do not account for the 1/2" telescoping when attaching each part.

For example; when building the veg unit "H," it specifies 7-7" pieces, but in the schematics it measures 7" between the "T's." I can either re-cut and allow for the extra 2" on each side (thus cutting 8" pieces to account for the 1/2" on the endcap and 1/2" for the "T") or drill holes 3" apart rather than 3 1/2." Does any of this matter? Thanks again to all for your help.
Click to expand...
Yes you need to add the inch to the specs or you will come up short. Hope this helps Good luck
 
D

Drifter126

Active Member
Nice work StinkBud Great Job.I`ve got one in my outbuilding,built out of hightimes 2009 grow guide.I`ve made one slight adjustment.I put a ball valve on both sides of the pump.Close back valve,open front to spray plants.Turn off front valve and open back valve and you can drain your res.with no hassles..This thing is GreatI even got a good deal on two 396gal.pumps.At 48"I have 10 sites to grow from.That gives me 20 grow sites for the whole setup.The rubbermaide tote and pump costs the most.The tote was about 12.00 bucks and the pumps were about 22.oo bucks,The 4X4 posts were 14.00.So all in all It`s a great system..++ REP
 
You must log in or register to reply here.
Top