CalWax
Active Member
open blaster(for now)
outdoor full nugs
ss tubes 1.1/4id.x 3ft power x5x .
southern california, across international 16x14 oven
So if you guys read everything you'd know i came into a couple large bags of outdoor material.
I got it divided up, full now and lowest micron sift in one bag, and more leafy material.
I have around 200-350 runs maybe more under my belt. I'm usually pretty good at producing a pretty consistent shatter.
but man this outdoor material has been throwing me through a loop....I'm sure it's more of my fault because i see
pros like xtracted run the almost identical looking slabs everytime....i think their closed loop with like a denatured alch dry ice bath maybe thats how they achieve the bright colors paired with s
almost uniform slabs, but i digress. So ive been doing light packing with both the nug and trim runs firm but nothing forceful. running three cans thru. right into non stick parchment sitting in
pyrex the water ranges from 125-135 so the oil hits it at about 110-120 for the inital bath.
I know I know, fuck me. Refining that part. I promise. I'm just trying to dial in my consistancys with low to no tane left in my final product.
so this most recent run. All nugs was a yield of about 90+ i followed as usual waited till it stopped acting up in the pan 4.8 quart pyrex for turkeys/
threw it in the AI at 44.5C and threw the vac on . the way the the oil was reacting was very uniform bubbles. not like your typical earl reactions. very uniform bubbles popping.
evacted a few times and lept getting the same, man i feel like a pretty big idiot. even after doing this as long as i have.
maybe the AI was too hot? i tried to follow gw/fd biblical 115 29.5
but the final result was 90 plus of some delicious sticky fire og sap. clean. very clean tasting. but sticky. and unbuyable by most clinics. although its a beautiful color
and is probably cleaner then anything they have they just hate the consitancy. f them. but any questions or comments weighing in would be killer.
outdoor full nugs
ss tubes 1.1/4id.x 3ft power x5x .
southern california, across international 16x14 oven
So if you guys read everything you'd know i came into a couple large bags of outdoor material.
I got it divided up, full now and lowest micron sift in one bag, and more leafy material.
I have around 200-350 runs maybe more under my belt. I'm usually pretty good at producing a pretty consistent shatter.
but man this outdoor material has been throwing me through a loop....I'm sure it's more of my fault because i see
pros like xtracted run the almost identical looking slabs everytime....i think their closed loop with like a denatured alch dry ice bath maybe thats how they achieve the bright colors paired with s
almost uniform slabs, but i digress. So ive been doing light packing with both the nug and trim runs firm but nothing forceful. running three cans thru. right into non stick parchment sitting in
pyrex the water ranges from 125-135 so the oil hits it at about 110-120 for the inital bath.
I know I know, fuck me. Refining that part. I promise. I'm just trying to dial in my consistancys with low to no tane left in my final product.
so this most recent run. All nugs was a yield of about 90+ i followed as usual waited till it stopped acting up in the pan 4.8 quart pyrex for turkeys/
threw it in the AI at 44.5C and threw the vac on . the way the the oil was reacting was very uniform bubbles. not like your typical earl reactions. very uniform bubbles popping.
evacted a few times and lept getting the same, man i feel like a pretty big idiot. even after doing this as long as i have.
maybe the AI was too hot? i tried to follow gw/fd biblical 115 29.5
but the final result was 90 plus of some delicious sticky fire og sap. clean. very clean tasting. but sticky. and unbuyable by most clinics. although its a beautiful color
and is probably cleaner then anything they have they just hate the consitancy. f them. but any questions or comments weighing in would be killer.
