new to ppm
- Thread starter MICHUSA
- Start date
MickFoster
Well-Known Member
My tap water has an EC of .3 which saves having to buy cal-mag.
NVGrower
Well-Known Member
I use 7.5 gallon tubs. We live in Nevada, terrible water quality. We use a under the sink reverse osmosis system.
When I change the water in my resivor every two weeks or so I use the 1/4" line that recirculates water into the pot and use it to empty the tubs. After adding new RO water to the tub the PPM read 100-118
When I change the water in my resivor every two weeks or so I use the 1/4" line that recirculates water into the pot and use it to empty the tubs. After adding new RO water to the tub the PPM read 100-118
rkymtnman
Well-Known Member
time to change your RO filters.
Skunk Baxter
Well-Known Member
Hah! That's how I knew my RO filter was bad; I was mixing nutes with tap water like I always do for the extra calcium, and on a whim I tested the RO as long as I had the TDS meter out anyway. RO came in at 110, and the tap water is consistently around 175. Went out and bought new filters the next day.
See, I thought I remembered changing them pretty recently, but evidently not. This time I got smart; I put a piece of painter's tape on the outside of the unit and wrote the date down.
OP - if you do decide to go with tap instead of RO, I second the suggestion that you get the water analysis. The geology of wherever you live will make a big difference in what minerals you have in your water. For example, if you live in an area where the geology is all limestone, your water will be high in calcium but may have almost no magnesium at all - so you'll still need to supplement your mag, and using calmag may not be your best choice because you're just wasting "PPM headroom" on extra calcium you don't need.
See, I thought I remembered changing them pretty recently, but evidently not. This time I got smart; I put a piece of painter's tape on the outside of the unit and wrote the date down.
OP - if you do decide to go with tap instead of RO, I second the suggestion that you get the water analysis. The geology of wherever you live will make a big difference in what minerals you have in your water. For example, if you live in an area where the geology is all limestone, your water will be high in calcium but may have almost no magnesium at all - so you'll still need to supplement your mag, and using calmag may not be your best choice because you're just wasting "PPM headroom" on extra calcium you don't need.
rkymtnman
Well-Known Member
good point. cal/mg is convenient in that it has both but sometimes you only need cal or mag.
NVGrower
Well-Known Member
I didn't dump it, switched the 1/4" pump line to a container I can dump. My point is with RO you don't have to dump it and your PPM is still less than 100 with the left over salts
Medicationist
Well-Known Member
Use Cyco and you won't have to worry about salts
NVGrower
Well-Known Member
Link?
Medicationist
Well-Known Member
I don't have a link, but it's a protein based nutrient, not salt based like pretty much every other product line on the market. It's crazy how clean your system stays when you ditch the salts.
rkymtnman
Well-Known Member
not sure what you are talking about. cyco are made from salts. bloom B is potassium nitrate and monopotassium phosphate.
Medicationist
Well-Known Member
Because it's a protein based nutrient, and it's pharmaceutical grade. Just because it has some salts in it doesn't mean it's salt based. There is very minimal amounts of salts, and it's an ionized salt. Check it out, you will be pleased with the results!
rkymtnman
Well-Known Member
the only 2 ingredients of bloom B are both salts, not proteins.
not saying cyco is bad, just that's it clearly salt based.
