Search results

When was the last time you flushed them? (Too many nutes ) Is it possible you’re over/under watering them (moisture stress ) I’ve heard some nutes can change the leaves and even the cola stems color ( no worries )

Well I just came back to see if you’d posted any updated potato pics and you did, of a 100% male plant. Better luck next grow man, and if you happen to get a fem seed raise it just as well as you did this one, just with better pics!

The easiest way is going to be to delete the post, but to answer your question it depends how you pollinate, if using a male plant you’re gonna get a half the genetics from each, and non fem seeds. Long story short use Colloidal Silver :)

Just from the pictures taken with a potato it looks to be male, it is possible that it’s a hermie. If I were you I’d hang on to it a little longer, until you get better pics, he’s a example of a male from one of my first grows

I’m in, good luck everyone!

I look forward to seeing your progress!

Spring is here, and my babies are almost ready for some outdoor soil!

I’m gonna agree with everyone else, good looking Grow. If I had a comment I’d say try to cool your tent a few more degrees. Auto’s seemed for me to grow a little slower between 65-75 degrees with 60%RH. That’ll help give the buds time to get bigger since you’re using less than 300watts in a 3x3...

HPS all the way until you get up to a 1,000watt led, your power bill will suffer but after a few decent grows then I’d go hard on led’s to save some money in the long run if you continue growing.

Looks like you’re off to a good start, my first grows forget how important RH, I know I did. Anyways I can see you got you’re gauge and starting right. What’s your light set-up?

Personal preference is to use twine and tie it off to a metal rafter or in my refrigerator hot box I put several metal eyelets used for that, but outdoors I’ve used wooden dowel rods or garden stakes with twine and tied them off just like tomato plants. The only thing I’ve avoid is metal wire...

Nothing sucks worst than losing your outdoor crop due to a early frost! :/ Looks like Endo for the win though!

I’m my honest opinion due to cost I’d probably go for a diy cob cfl, you can use 5 14watt for seedlings, clones, and some vegging, then swap them out for 42watt during pre flower vegging, and the flowering phase.

I always soak my seeds even though it isn’t recommend. Just make sure not to leave them in their for more than 48 hours our you’ll likely be dead due to drowning. Also some light sandpaper or match box box can be used along the edges of the seed before soaking

I'm afraid there're too many variables, but if you're seeing buds I'd definitely get that light close, that'll help and possibly help strengthen your root system and stem before you go into a full bloom

Definitely agree the temps are a bit high, but I'd like some more info. such as what strain are you're growing, how close is your light (230w should be able 30" from seedlings), how much air are you truly moving (cfm) and what soil and nutes you're using

Definitely agree insects could become a issue, you could also add some blue led light if it's in your budget, can't remember the NM because I'm stoned, but it'll help reduce the chance of pests and mold

I've grown some blue dream and purple haze, but I never crossbred them. Both stains were easy to clone but I had issues with harvesting. I harvested a bit earlier than a should have, a little because they were harder to tell when the trichomes where clouding, and a little because I was ready to...

If you include a few more details and pictures I can probably assist you better, but this should help. Air should be exchanged every one to 3 minutes +/- depending on you grow size, temp., relative humidity. GROW SPACE SIZE WATTAGE OF LIGHT CFM OF FAN 2’ x 4’ x 5’ 250W 80-120 CFM 3’ x 3’ x 6’...