Cutter Electronics: Complete DIY COB kits

Kenpark

Well-Known Member
hi i just ordered a mau X kit a 4x4 space (Homebox 120cmX120cmX200cm )you can give me a drawing with installation dimensions I read something of a double H setting thanks .....
 
Last edited:

SidLascivious

New Member
Great thread, and great information!

I am looking at ordering 2 x MAU5-IV NPS (No driver) and running them off of an MW HLG-600. Does the coupon code mentioned in the original post still work with these kits? Also, are there any additional shipping options or is $125 the standard number shipping AUS->US?
 

1gfunk1

Active Member
Hi welight am looking at chamgeing my 3 600 watt hps 1800wAtt witch I average off 1500 grams off in a 2.2 m tent ! It's 23 total square feet tent ! am looking at the cree 90 cri chips 3000k bulbs but don't now witch drivers to get most power out off my leds was thinking off 12 - 16 cree bulbs running at 75 watts think that will add up to 1500 grams that I get with my 1800 watt hps !? Any help would be great just don't won't to change my parabolic hps without getting near my old yields !? Raver take my time and get it rite ! Thanks


Tent is like nearly 8 feet long 3 wide so it's narrow tent but long
 

Malocan

Well-Known Member
Hi Mark @welight

I saw you allready listed the Vero Decor 1700k @ your shop. I will order soon 10 of them, but now i wonder is it possible that you can order this vero BXRC-56G10K1-C-74-SE too? i would like to order 10 of them too.

greetings Malocan
 

welight

Well-Known Member
Hi Mark @welight

I saw you allready listed the Vero Decor 1700k @ your shop. I will order soon 10 of them, but now i wonder is it possible that you can order this vero BXRC-56G10K1-C-74-SE too? i would like to order 10 of them too.

greetings Malocan
yes, I have not put up all the parts I have on order, time poor, will try to complete today, thanks for your interest
Cheers
Mark
 

welight

Well-Known Member
Hi welight am looking at chamgeing my 3 600 watt hps 1800wAtt witch I average off 1500 grams off in a 2.2 m tent ! It's 23 total square feet tent ! am looking at the cree 90 cri chips 3000k bulbs but don't now witch drivers to get most power out off my leds was thinking off 12 - 16 cree bulbs running at 75 watts think that will add up to 1500 grams that I get with my 1800 watt hps !? Any help would be great just don't won't to change my parabolic hps without getting near my old yields !? Raver take my time and get it rite ! Thanks


Tent is like nearly 8 feet long 3 wide so it's narrow tent but long
Hi1gfunk
our 24 up kit at 1200watts would do the trick in an 8x 3 strip pattern, 50 watts per would be more than enough, does that make sense
Cheers
Mark
 

goofy81

Well-Known Member
I'd go A if i could bend all the outside COBS to a bit of an angle.
But A looks like the obvious choice.

What about..


"O O O"

" O "
"O O"
" O "

"O O O"

Decisions, decisions, decisions.... .
edit ok that didnt work out right.
I tried to do 3 colums
First column 3 lights down, second column 4 lights, 3rd column 3 lights.
 

1gfunk1

Active Member
Hi1gfunk
our 24 up kit at 1200watts would do the trick in an 8x 3 strip pattern, 50 watts per would be more than enough, does that make sense
Cheers
Mark
And if I could buy 1 , 8 light kit at a time till I get all three how much it be one 8 light kit !? And would it be best to use the new veros and run the lights at 75 watt !? Use less lights !?
 

VegasWinner

Well-Known Member
I love to see all of these kits going out the door. In the 8-cob layout, I have found the perimeter layout works best with no center cob and I use supplemental lighting on the edges of the canopy wiuth far red in the middle.
 
Top