Recent content by Quiller

I'm sick of these clubs getting their way forcing consignment because if you don't do it, the next will. Well I'm talking to you "next guy"... KNOCK IT OFF!!!! These clubs get free inventory, make over 100% profit margin and then act like they don't have to pay you till they're ready???? COME...

Good job man, excellent outdoor setup. I usually spend time reading through the indoor section cause I don't have space for outdoor that's safe. WIsh I did after seeing yours, you gotta post what you yield when done. here's my indoor setup...

Well, I thought possibly too small of pots, but I have 2 others that I put in much larger pots and they are still young. Same thing is happening to them. It seems like a disease that is spreading. I have since separated them. I have flushed more. We will see......

It's spreading to the others as well. I am wondering if it is a disease of some kind. They are my hydro pots for now in coco and perlite. I feed them GH 3 part growth solution every 3rd watering and water on the others. I flushed them all at the first signs of trouble and it has continued to...

Ok, sounds good. I will add the H2O2 and Ph adjust. I am a little worried about not using domes. Whenever I have left them off in the past before roots were apparent, they wilted within an hour. Is there a way to avoid this?

Yes, the domes have vents. But don't forget, the stems are not drying up, they are turning to slime from the mildew and mold. 2 years I have cloned this way. I simply change locations and mildew/mold steps in.

I have enjoyed the last 2 years successfully cloning everything I stuck in a Jiffy Pellet. I keep it very simple and have had 98% success rate. That is, the whole time I did this at my shop. Now that I am trying to do a few trays at home, it is a whole different story. I use Jiffy Pellets...

There are sides on the table, about 3" high. Then wrapped and stapled with plastic. I wanted more space than a standard 4 x 8 tray so I built my own 4x12.

Yeah, in the 90's today. Had to check all my fans and coolers.

I did the same. I made a plywood and 2 x 4 table that is 4' by 12' with 4" sides. Offset at an angle so it all drains to one edge and towards the far corner. I use a strip of plastic gutter to catch all the runoff and direct it to the reservoir. I lined the table with panda film and stapled it...

Great, thanks. I am also going to make a hinged cover for my rez for added protection against the algae factor... lol I know that having the light shine on the rez is what's promoting it. I just thought there was something else wrong. I saw a hydro system of a friend of a friend situation and...

Yeah, let's get over it. An ignorant conversation takes two... lol Can anyone share ideas on how I can add Floraliciuos to my hydro system without gumming up my rez? Should I make a separate mix and give a couple cups per plant? Foliar feed? Add to the rez with H202? I don't know, I do want...

I am curious how one uses the Floralicious..... I added it to the rez and within 24 hours the algae was so thick my pumps locked up. Do you guys foliar feed with it or pour it into the pots by hand? Or is this where you use the H202 to control it......

Well I cleaned it up. Alcohol in the rez and washed everything. Reloaded with nutes minus the flora nectar. Any suggestions on how to use it without getting the algae growth?

Drip system with cocoa drain to rez..... I use GH 3 part and not had this problem before. I added Flora Nectar this time and by the next day I have snot all over the walls and pumps. Clogged up the lines and requires complete clean up. What the Hell????? Yeah, I need a cover for the rez but I...