Recent content by fehasleedz

I read he was using the auto pilot co2 controller, which DOES have a day/night function Controller was set up for day function, have the generator turned off, sealed up all water heater this has to make sure it's not causing excess co2

Glad I asked! It's the water heater for sure man. No question about it. Get that thing moved or seal the shit out of the ceiling. Turned off my burner last night and checked my ppm monitor. WHen lights were on they CO2 went way down, lowest levels ive seen. I think when people shower the...

Glad I asked! It's the water heater for sure man. No question about it. Get that thing moved or seal the shit out of the ceiling. Really hoping this is the last missing piece of my puzzle.

Glad I asked! It's the water heater for sure man. No question about it. Get that thing moved or seal the shit out of the ceiling. I'll take pics of the room and how the heater sits above it. Will report back once I've taken a few pics.

To be honest, I do not know. I don't use burners. I looked it up real quick and that's what I found. Tell me every single thing in your room. Something else must be the source. 2 de humidifiers 9 1000 W HPS lights (ballasts outside the room) 1co2 controller 8 burner co2 generator 150 can...

Did you adjust your pressure on the natural gas line? It's supposed to be 4.5" WC or 1/4PSI How do I even do that? That is new to me. Could that be the problem is the line is not up to those standards? Problem is numbers were high even before gas was turned on

[QUOto Carolina Dream'n, post: 12061389, member: 890973"]Is there a flow rate on your generator? Not sure.... I have this one.. Do you think if the plants are getting 3k plus ppm for a couple hours a day it would make thier leaves get chlorosis? Not sure this is the one i have...

It was 1300 when I got in today, about 2 hours into the light coming on. And same here, if I'm in the room, especially if another is too, the ppm can go upwards of 3500 pretry quick. My room is legitimately Sealed.

Electronic ign. Will drop the sensor. And report back

I'm using an autopilot 8 burner and autopilot controller... http://www.horticulturesource.com/product_info.php?products_id=16984&gclid=CjwKEAiA64uyBRCVmKyT2vuAjzgSJADfINB6yAmaESgrn0124YickRcS5-vhQ-0xxJshk-Jp-i-9LRoCDLDw_wcB The sensor is hanging in between lights, middle of the room. About...

Agreed, plants have been flushed, but the yellowing chlorosis is the problem. Thrips is an issue too but using azamax root drenched and spraying thrm to take care of that. Just can't figure out why the co2 levels are so dam high and the burner doesn't even come on.

Yes calibrated it outside and it went down to 430 ppm. I just can't figure out why the co2 levels are so high. Doesn't make any sense.

OK, so what can I do? My room is sealed, no way to vent. Co2 burner doesn't come on.

I am in week 4 of flowering. Had a thrip problem and still battling it. Sucks Cuz my whole set up is sealed, both veg and flower. Using soil, plants are in 5 gal containers. 14 12 room and Have 9 1000 w lights, 3 plants under each light. The video below is a Co2 monitor and takes a log of...

Thanks for your reply, to get it straight I need to flush with 7.0 water but flush with nutes? I use the foxfarm diet. What nutes should I use while I flush? WHen i flushed last time it took alot of water! just to get it to 6.0. So i just need to flush until my plants runoff is 6.5. Im...