Led Users Unite!

Nugachino

Well-Known Member
Not to seem like a retard. But, it sounds like you're saying that 200~250w is about what I need?

If that's the case. Am I still better off going the 400w unit and just turning it down. Or running the 200w at capacity?

I'm new to growing. And never thought I'd even use led technology to grow with.
 

frica

Well-Known Member
This seems like the place to ask.

I'm probably going to buy a tent that's just under 2 square feet. And 5.5ft tall. As I'm only going to be supplying for myself.

I'm looking at a COB kit from Cutter. How many watts do I need to saturate this grow space? I'm not great at the whole mathematics thing.

I was thinking about getting the 400w kit since it's only about $120 dearer than the 200w. And I can turn it down as needed.
Does that sound okay?
2 by 2 feet.

Or really just 2 square feet?

35-50 watt for every square feet.
So 70-100 watt, if it's just 2 square feet.

You should turn both down anyway, 200w would probably already be too much for that little space.

You could also get something from another vendor.
https://northerngrowlights.com/collections/all/products/photon-180v-gen-7?variant=25843297480
Is a great light. (Also has to be turned down, if really just 2 square feet)

Shame it's out of stock because this light would have been ideal for such a small space.
https://www.tastyled.com/Tasty-T1-2100-LED-Grow-Light-p/t1-v196.htm
 

DesertHydro

Well-Known Member
i would always go overkill if its in the budget. you can always raise the lights for better coverage or dim them down. plus if you get a little bigger space eventually it will help bridge the gap and not feel so antiquated.
 

lex660nm

Active Member
i would always go overkill if its in the budget. you can always raise the lights for better coverage or dim them down. plus if you get a little bigger space eventually it will help bridge the gap and not feel so antiquated.
me too, overkill and extra co2, also i use AN b-52 and rhinoskin to combat heatstresses and other stressors that may occur plus stretch is shortened With Shorter internodal distance :)

happy newyear
 

hillbill

Well-Known Member
My Photon 180 would kill 4 sq ft and provide even, intense light with a great spectrum! I have a citizen 3500k 90cri. Love the boost in reds spectral wise. Getting great frost under this light with strains I've had for 5 years. I think the new Veros have a similar shift. I've been using LEDs and COBs for a while now and did not expect the heavier trichs still, but that has been consistent.

Quantum boards would be awesome in that area. Maybe awesomer even!
 

lex660nm

Active Member
amaretech
budmaster
sunplusled
duolux
northerngrowlights
grownorthern

and ALOT of other brands would also do an amazing job, not just one brand or approach:)
 

Gromax 3590B

Active Member
Happy new year to u all. I am boozed out with friends now but all the guys and girls in America yet have to start their party's. Have a good and safe yearchanging.
 
Last edited:

flodas

Well-Known Member
Need some inputs on my light and space. I have recent bought and build a vero kit 400w from timber 100w on each cob.

My grow room is 1.2 square meeters i have put the cobs in a square in with one cob in each corner. There is 16 inches betwen each cob and I run them without any reflectors or lenses for beter spread.

Any improvments or inputs would be appreciated? / flodas
 

goofy81

Well-Known Member
Day 29 at the moment and I'm noticing trichomes on my leaves are like 10% Amber! Could the trichomes on leaves be more mature than the bud because they popped out earlier? Anyone experienced this before?
 

Malocan

Well-Known Member
Day 29 at the moment and I'm noticing trichomes on my leaves are like 10% Amber! Could the trichomes on leaves be more mature than the bud because they popped out earlier? Anyone experienced this before?
im pretty sure, i saw that too on my leaves. I think this is normal but im not sure :/
 

lex660nm

Active Member
i think so too, pretty normal that some buds gets amber before others so i think its logical too With leaves
at least not any negative sign i can think of
 

greg2k

Active Member
I've been looking and reading all over the internet for a couple of days now, and the results from these COB-lights look truly amazing!

DIY definitely seems like the way to go if u want to get your money's worth, and so i've decided to build a light for myself!

My budget is around $700 and i'm aiming for a 900 ppfd average, which should be doable, according to the COB calculator (if i managed to use it correctly...) Might aswell post the data i guess.
Citizen.1812C4.3000K 8 COBS @1.05A ON 1.813 PROFILE HEATSINK
1 SQ.M. CANOPY 91% EFFICIENT DRIVER @0 CENTS PER KWH
Total power watts at the wall: 484.62
Cobs power watts: 441
Total voltage forward: 420
Total lumens: 66150
Total PAR watts assuming 10% loss: 182
Total PPF: 884.52
PPFD based on canopy area: 884.52
PAR watts per sq.m.: 182.0
Cob efficiency: 45.84%
Power watts per sq.m.: 441.0
Voltage forward per cob: 52.5
Lumens per watt: 150.0
Heatsink riser thickness / number of fins / fin's length: 0.3in/6/0.95in
Heatsink area per inch: 100.94 cm^2
Total heat watts: 239
umol/s/W / CRI: 4.86 / 80CRI
Heatsink length passive cooling @120cm^2/heatwatt: 284 inches
Heatsink length active cooling @40cm^2/heatwatt: 95 inches
COB cost dollar per PAR watt: $1.01
Electric cost @12/12 in 30 days: $0.5
Electric cost @18/6 in 30 days: $0.5
Cost per cob: $22.93
Heatsink cost per inch cut: $0.66
Total cobs cost: $183
Total heatsink passive cooling cost: $187
Total heatsink active cooling cost: $62

What design would give the most even light distribution across the canopy? Outer rows with 3 COBs and the center one with 2? Grow space for this light will be 3x3 foot / 90x90 cm.

I've been contemplating a lot on how many cobs i need, what drivers, and so far i've come up with the following shopping cart on cobkits.com

8 pcs Citizen CLU048-1818 80CRI
2 pcs MeanWell HLG-185H-48A Driver (which would run the cobs at 55W each)
8 pcs BJB holder for CLU048 series
8 pcs LEDiL Angelina reflector for BJB Holder (Citizen CLU048 )
8 pcs Arctic thermal pads for Citizen CLU048 series
8 pcs 120mm Passive Pin-fin heatsink
~$520 + $110 shipping.

Am i on the right track, or would you guys do it differently in a 3x3 space?

/greg :p
 

JayY2015

Well-Known Member
hello guys I need a little help if I have two leds that equal 969 PPFD for a 4x4 what would it be if I put it on a light mover over a 4x6 area?
 

cuddlesthesheep

Well-Known Member
Hey guys, looking to add a veg tent to go along with my 5x9 with 2 JGL Maximizers. Figured a 5x5 would be a good size. Just wondering what would be a good option from timber. Guessing a spectrum closer to 5k since it would be dedicated to veg. Interested in these Vero's they got but to be honest haven't looked up on the LED game since i bought the maxi's.

Thanks in advance guys.

PEACE
 

lex660nm

Active Member
i think your spot on with outer 3 and center 2!but from what i know you can get more par pr watt and lumens with cxb 3070 topbins or 3590 or the new 200w max cxb topbin. and it should go with that budget too
I've been looking and reading all over the internet for a couple of days now, and the results from these COB-lights look truly amazing!

DIY definitely seems like the way to go if u want to get your money's worth, and so i've decided to build a light for myself!

My budget is around $700 and i'm aiming for a 900 ppfd average, which should be doable, according to the COB calculator (if i managed to use it correctly...) Might aswell post the data i guess.
Citizen.1812C4.3000K 8 COBS @1.05A ON 1.813 PROFILE HEATSINK
1 SQ.M. CANOPY 91% EFFICIENT DRIVER @0 CENTS PER KWH
Total power watts at the wall: 484.62
Cobs power watts: 441
Total voltage forward: 420
Total lumens: 66150
Total PAR watts assuming 10% loss: 182
Total PPF: 884.52
PPFD based on canopy area: 884.52
PAR watts per sq.m.: 182.0
Cob efficiency: 45.84%
Power watts per sq.m.: 441.0
Voltage forward per cob: 52.5
Lumens per watt: 150.0
Heatsink riser thickness / number of fins / fin's length: 0.3in/6/0.95in
Heatsink area per inch: 100.94 cm^2
Total heat watts: 239
umol/s/W / CRI: 4.86 / 80CRI
Heatsink length passive cooling @120cm^2/heatwatt: 284 inches
Heatsink length active cooling @40cm^2/heatwatt: 95 inches
COB cost dollar per PAR watt: $1.01
Electric cost @12/12 in 30 days: $0.5
Electric cost @18/6 in 30 days: $0.5
Cost per cob: $22.93
Heatsink cost per inch cut: $0.66
Total cobs cost: $183
Total heatsink passive cooling cost: $187
Total heatsink active cooling cost: $62

What design would give the most even light distribution across the canopy? Outer rows with 3 COBs and the center one with 2? Grow space for this light will be 3x3 foot / 90x90 cm.

I've been contemplating a lot on how many cobs i need, what drivers, and so far i've come up with the following shopping cart on cobkits.com

8 pcs Citizen CLU048-1818 80CRI
2 pcs MeanWell HLG-185H-48A Driver (which would run the cobs at 55W each)
8 pcs BJB holder for CLU048 series
8 pcs LEDiL Angelina reflector for BJB Holder (Citizen CLU048 )
8 pcs Arctic thermal pads for Citizen CLU048 series
8 pcs 120mm Passive Pin-fin heatsink
~$520 + $110 shipping.

Am i on the right track, or would you guys do it differently in a 3x3 space?

/greg :p
h
 

Seedman06

Member
Hello.

New grower here I have two 60*5 watt led panels(Apollo and Mars hydro mars300) approximately 270 true watts over a 2ftx3.5ftx 6ft tall space for flower.

I have just started my grow and have my plants vegging. I was wondering if that would be adequate lighting for the space or if I would be better off using one of the led panels for vegetation/mother (2x2.5x4 ft tall space.) And picking up a mars reflector 96 or 144 to use for flower with the other 60*5 panel?
Thanks for any advice!
 

LSD-25

Well-Known Member
First full LED grow. Day 22 of 12/12

Looking awesome. No nute burn, very minimal yellow leaves, fed every hour.
Plants have never been more healthier. Always struggled a bit under hps but no longer.
That is what I am talking about MAN!!!! nice as hell... this is the kind of stuff that has me thinking about switching to LEDs.. see... I'm just getting back into growing and I am using ALL my old equipment. I even still use a 100 watt magnetic ballast for one of my lights... lol . I am thing about the Black Dog line of LEDs .. I saw a youtube video where it out performed a Kind LED.. lets rap.
 
Top