Twitch Extracts pneumatic press

Twitch

Twitch

Well-Known Member
i think the contact points are what makes it more.... if that makes sence....

your foot may be on a 3.5 by 4.5 surface area but the areas that are touching and where the force is actually applied and concentrated is smaller
 
Last edited:
Twitch

Twitch

Well-Known Member
If you can open the pdf file in the comment 206 it is a 3D picture of the plates, you can rotate it and look at it from any view
 
Bugeye

Bugeye

Well-Known Member
I'm questioning the psi calculations in this thread in regards to bench block size. In actual use isn't the size of the material being pressed the determinant of psi? There is no pressure on the surface area outside the materials footprint, is there?
 
hyroot

hyroot

Well-Known Member
Bugeye said:
I'm questioning the psi calculations in this thread in regards to bench block size. In actual use isn't the size of the material being pressed the determinant of psi? There is no pressure on the surface area outside the materials footprint, is there?
Click to expand...

No. The plates have to touch each other to create that much psi. If all the pressure was on the material. Then the plates wouldn't touch and then there would be very little psi if any
 
Bugeye

Bugeye

Well-Known Member
hyroot said:
No. The plates have to touch each other to create that much psi. If all the pressure was on the material. Then the plates wouldn't touch and then there would be very little psi if any
Click to expand...
I don't understand how the plates could be touching each other if there is material being pressed. Compress it paper thin and you'll still have a paper thin gap between the plates, no?
 
Bugeye

Bugeye

Well-Known Member
hyroot said:
No. The plates have to touch each other to create that much psi. If all the pressure was on the material. Then the plates wouldn't touch and then there would be very little psi if any
Click to expand...
Maybe I'm assuming material will not spread over the full area of the bench block, and in reality it really does? I have not run at high pressure yet so I'm going from bench clamp observations. :bigjoint:
 
hyroot

hyroot

Well-Known Member
Bugeye said:
Maybe I'm assuming material will not spread over the full area of the bench block, and in reality it really does? I have not run at high pressure yet so I'm going from bench clamp observations. :bigjoint:
Click to expand...

With say 2x2" or 2x 4" plates and depending how much you are pressing. It should spread out all over the surface area if not doing waterfall tech. A paper thin gap is less than a decimeter. Which I don't think would affect the psi at all.
 
Bugeye

Bugeye

Well-Known Member
hyroot said:
With say 2x2" or 2x 4" plates and depending how much you are pressing. It should spread out all over the surface area if not doing waterfall tech. A paper thin gap is less than a decimeter. Which I don't think would affect the psi at all.
Click to expand...
Ah, got it. That makes sense then. Cheers!
 
hyroot

hyroot

Well-Known Member
I guess the guys at norstar genetics got burned twice by rosin technologies. Now people are getting burned by rosin works too. .
 
Aqua Lab Tech

Aqua Lab Tech

Well-Known Member
hyroot said:
I guess the guys at norstar genetics got burned twice by rosin technologies. Now people are getting burned by rosin works too. .
Click to expand...
Once again you are spreading false information. The guys at Norstar Genetics were "burned twice" by Rosin Tech Products, not Rosin Technologies.
 
hyroot

hyroot

Well-Known Member
Aqua Lab Tech said:
Once again you are spreading false information. The guys at Norstar Genetics were "burned twice" by Rosin Tech Products, not Rosin Technologies.
Click to expand...
Its not spreading. But it did say rosin technogies right when he posted it earlier. He must have changed it. . But ima ask scotty right now to make sure I'm not tripping. Insta does auto correct when tagging people .



It does say rosin tech products now.

I never ever once spread a rumor before. You just tried to cover your ass. Instead of being truthful. We'll leave it at that.

All the proof was already posted on this forum.
 
Aqua Lab Tech

Aqua Lab Tech

Well-Known Member
hyroot said:
Its not spreading. But it did say rosin technogies right when he posted it earlier. He must have changed it. . But ima ask scotty right now to make sure I'm not tripping. Insta does auto correct when tagging people .



It does say rosin tech products now.

I never ever once spread a rumor before. You just tried to cover your ass. Instead of being truthful. We'll leave it at that.

All the proof was already posted on this forum.
Click to expand...
Did you ask Scotty or get a response from him? Not sure how he could of changed the comment without deleting or making a new comment and still be the first comment? I am also not really sure why you felt the need to run and post something from IG on this thread, especially when your wrote incorrect information about another company?
 
You must log in or register to reply here.
Top