BHO YIELDS

personal lux

Well-Known Member
Lets here them! Give details! Show us your biggest and prettiest runs!
Average for bud 6g/oz
average for good sugarleaf/ buds is about 3-4g/oz.
Average trim small fan leafs not a lot of bud about 1.5-2g/oz

These are my averages everything is vac purged 24+ hours. Got about 20zips of some flame sugar and bud to blast so ill have that up in not to long!
 

Flagg420

Well-Known Member
Trim n fluffy buds i usually end up with about 2-2.5g after winterizing... I use a G pen so I like a nice shatter texture...
 

patrickkawi37

Well-Known Member
I don't make mine but I get half of the yield from the dude that makes it. I normally get a little over an ounce per pound of sugar shake. So he yields anywhere between 2-2.5 ounces per 450 grams
 

torontoke

Well-Known Member
I found that different brands of butane actually effect the yield.
Using my favorite brand id say i average about the same as you.
Usually 4-5 grams an ounce of shake and sugar leaves.
2-3 grams if theres next to no bud and its just leaves.
 

personal lux

Well-Known Member
I found that different brands of butane actually effect the yield.
Using my favorite brand id say i average about the same as you.
Usually 4-5 grams an ounce of shake and sugar leaves.
2-3 grams if theres next to no bud and its just leaves.
I have had good results with luciene, vector, puretane, and stok brands. Highest yield ive had was 8 oz of buds/trim got me 36grams of shatter.
 

GreenStick85

Well-Known Member
Hope you got a vac, I find just doing BHO alone is smelly. The product just reeks of the solvent and I've tried taking the most filtered stuff I can find around here. I've resorted to using ethanol now that Most can't purge with just hot water alone.
 

R&RHashman

Well-Known Member
looks very tasty VTM. and green I have never had underpurged BHO and I know I have tasted both vac chamber and non vac chamber so maybe you should buy from a better guy?
 

personal lux

Well-Known Member
Hope you got a vac, I find just doing BHO alone is smelly. The product just reeks of the solvent and I've tried taking the most filtered stuff I can find around here. I've resorted to using ethanol now that Most can't purge with just hot water alone.
Cant do without vac my friend. I have the shatter vac from bestvaluevacs. 3 gallon with digi heat pad, and 3cfm pump.

I really liked the outcome from puretane. but luciene, or vector seems just the same now. And its cheaper by far.
 

7mend07SweetnSticky

Well-Known Member
personal lux said:
I run my purge at like 28 so i figure its not necessary
If your not heating to atleast 110°F with the 3 cfm pump. I'd bet there's still butane in it. But the purpose of the 6 cfm pump is to get a stronger pull to be able to pull the butane out of the oil with lower heat. Bringing the quality up with less time. As apposed to 110°F for 16-24+ hours. Should be able to purge with less time and heat to still get a clean product
 

yodabuds

Well-Known Member
Personal Lux I just got the exact same
Set up awaiting a 45g closed pressurized column this week... Hopefully it will help increase my yield a little bit.... I am finding I either have a crappy laser thermostat or the heating mat sometimes seems "off" could just be me or my method.... It's all a learning process and I'm a noob... So trying all sorts of different things
A couple indica autos I ran got like a crumble consistency
image.jpg
And the gth trim that I'm still purging at different temps and times
image.jpg
Still purging some
image.jpg
Will see what it comes out like
Just need to get an e nail now, been looking at some of the Chinese ones over dhgate any suggestions ????
 

personal lux

Well-Known Member
Personal Lux I just got the exact same
Set up awaiting a 45g closed pressurized column this week... Hopefully it will help increase my yield a little bit.... I am finding I either have a crappy laser thermostat or the heating mat sometimes seems "off" could just be me or my method.... It's all a learning process and I'm a noob... So trying all sorts of different things
A couple indica autos I ran got like a crumble consistency
View attachment 3445140
And the gth trim that I'm still purging at different temps and times
View attachment 3445141
Still purging some
View attachment 3445142
Will see what it comes out like
Just need to get an e nail now, been looking at some of the Chinese ones over dhgate any suggestions ????
Stuff looks realllyyy dark. Make sure you start temaos at 90 and bring them up of you need too.
 
Top