Forum Shop Market
Seeds FAQ Tools
SEE OUR MARIJUANA SEED GUIDE FOR THE BEST STRAINS
Looking for Legal Marijuana look no further!
Go Back   Marijuana Growing > The Grow Room > Indoor Growing


Reply
 
LinkBack Thread Tools Display Modes
  #1    
Old 08-09-2007, 05:40 PM
GetAhead's Avatar
Marijuana Toker
Marijuana Toker
GetAhead is offline
 
Join Date: Jul 2007
Location: Bay Area, CA
Posts: 110
GetAhead is on a distinguished road
Points: 1,523, Level: 5 Points: 1,523, Level: 5 Points: 1,523, Level: 5
Activity: 0% Activity: 0% Activity: 0%
Default Possible Room Setup
Recently moved into a new place and had a few option locations for establishing a grow room. Long story short, and for various reasons, it has come down to a former pool shed measuring 8.5’ X 7’ X 8’. Love to have more room, but I could have less, too. Anyway, I will HAVE to make this do for now. Here is the equipment I have:

600W Air-Cooled HPS/MH Reflector and Digital Ballast
8” Elicent Inline Fan (686 CFM - not as quiet as I had hoped)
8’ PHAT Filter (550 CFM)
2 - 14” Oscillating Fans
5 - 3” Low Voltage Circulation Fans
3 – 4’ Fluorescent Hoods with AgroGrow tubes
Full complement of other accessories and nute

I have divided the room in to two section – one seedling/veg, one flower. Attached are top and front views of the plan. On the veg side, I am planning on having a subsection for two mother plants and two subsections for trays holding clones – each installed with heavy duty drawer rollers and folding support rods so that the shelves can be slid out to gain better access. On the flowering side, I figure there is room for 16 plants MAX (depending on grown out size) though my first go round I will likely go with 12. This would seem, to me, to be a plausible, workable deal on a theoretical basis. OTOH, while I’ve had lots of experience growing other things – I’m a first timer when it comes to weed.

My seeds just arrived today and I am planning to do some room setup this weekend. I would appreciate and input you all might have before I get started. Would be happy to supply more information, if needed. As always, thanks in advance.
Attached Images
File Type: jpg SUTWeb.jpg (94.0 KB, 28 views)
File Type: jpg SUFWeb.jpg (79.1 KB, 20 views)
Reply With Quote
  #2    
Old 08-09-2007, 07:19 PM
HoLE's Avatar
Mr.Ganja
Mr. Ganja
HoLE is offline
 
Join Date: Jul 2007
Location: central ontario
Posts: 3,006
HoLE has much to be proud ofHoLE has much to be proud ofHoLE has much to be proud ofHoLE has much to be proud ofHoLE has much to be proud ofHoLE has much to be proud ofHoLE has much to be proud ofHoLE has much to be proud of
Points: 44,694, Level: 30 Points: 44,694, Level: 30 Points: 44,694, Level: 30
Activity: 1% Activity: 1% Activity: 1%
your already on the right track,,just by planning first,,I'm sure you'll get answers here,,I did

Keep on Growin

HoLE
Reply With Quote
  #3    
Old 08-09-2007, 10:50 PM
VictorVIcious's Avatar
Super Stoner
Mr. Ganja
VictorVIcious is offline
 
Join Date: Sep 2006
Location: Northeastern USA
Posts: 5,892
VictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond reputeVictorVIcious has a reputation beyond repute
Points: 75,470, Level: 39 Points: 75,470, Level: 39 Points: 75,470, Level: 39
Activity: 0% Activity: 0% Activity: 0%
welcome to the forum. You have obviously done some research. And your drawing, can you send me that software, that is great. I would recommend that you start with the basics. Plumbing system, electrical system, air handling sytem. Install those first for obvious reasons. Word of advice from some one that didn't understand, do not put controls or plugs you need to get to behind the plants or locate switches and shut off valves some where else, like your sink, working area. Plugs for fans etc. might be better on the ceiling if possible.
If those are actual walls you are planing I wouldn't recommend them. Panda plastic movable curtians will work and still keep everything flexible. Unless you are using soil you should be able to flower 24 plants under that light.
You can make drawers to slide the clones out, you will probably find it just as easy to move them to a table that is normal height when you 'work on them' anyway. I take it your plannning on waiting until your first crop is done before you put more plants in the system. 8 to 12 weeks in veg is a long time.
What system, ie flood and drain , soil, aero are you planning on using?
Here is a picture of plants an a 32" by 4' table under a 600 watt equivalant light. The pots are one gallon. VV
Attached Images
File Type: jpg MVC-010S.JPG (55.7 KB, 14 views)
Reply With Quote
  #4    
Old 08-10-2007, 12:30 AM
GetAhead's Avatar
Marijuana Toker
Marijuana Toker
GetAhead is offline
 
Join Date: Jul 2007
Location: Bay Area, CA
Posts: 110
GetAhead is on a distinguished road
Points: 1,523, Level: 5 Points: 1,523, Level: 5 Points: 1,523, Level: 5
Activity: 0% Activity: 0% Activity: 0%
Quote:
Originally Posted by VictorVIcious View Post
welcome to the forum. You have obviously done some research. And your drawing, can you send me that software, that is great. I would recommend that you start with the basics. Plumbing system, electrical system, air handling sytem. Install those first for obvious reasons. Word of advice from some one that didn't understand, do not put controls or plugs you need to get to behind the plants or locate switches and shut off valves some where else, like your sink, working area. Plugs for fans etc. might be better on the ceiling if possible.
If those are actual walls you are planing I wouldn't recommend them. Panda plastic movable curtians will work and still keep everything flexible. Unless you are using soil you should be able to flower 24 plants under that light.
You can make drawers to slide the clones out, you will probably find it just as easy to move them to a table that is normal height when you 'work on them' anyway. I take it your plannning on waiting until your first crop is done before you put more plants in the system. 8 to 12 weeks in veg is a long time.
What system, ie flood and drain , soil, aero are you planning on using?
Here is a picture of plants an a 32" by 4' table under a 600 watt equivalant light. The pots are one gallon. VV

Thanks for the input Double V. I am going soil the first go around as I want to more carefully plan and construct a hydro system, but I want to get going now to obtain some product quickly. Yes, this setup would be the ultimate fruition, knowing that a mother or two and clones would come after vegging the first time. I appreciate what you are saying about walls but I want a flowering area that is light sealed so that vegging can take place in the same structure. Too, the one wall will serve as support for the clone/seedling shelves. I do like theidea of the Panda screens being a bit more flexible, so to speak, but the need for the area to be light proof is trumping all those type of ideas I've had, so far.

Your grow looks tasty. The software I used is Adobe Illustrator (expensive) but much cheaper graphics programs will do.
Reply With Quote
  #5    
Old 08-10-2007, 12:38 AM
Gygax1974's Avatar
Just some idiot
Mr. Ganja
Gygax1974 is offline
 
Join Date: Jun 2007
Posts: 2,433
Gygax1974 is a jewel in the roughGygax1974 is a jewel in the roughGygax1974 is a jewel in the rough
Points: 10,278, Level: 14 Points: 10,278, Level: 14 Points: 10,278, Level: 14
Activity: 0% Activity: 0% Activity: 0%
Quote:
Originally Posted by GetAhead View Post
Thanks for the input Double V. I am going soil the first go around as I want to more carefully plan and construct a hydro system, but I want to get going now to obtain some product quickly. Yes, this setup would be the ultimate fruition, knowing that a mother or two and clones would come after vegging the first time. I appreciate what you are saying about walls but I want a flowering area that is light sealed so that vegging can take place in the same structure. Too, the one wall will serve as support for the clone/seedling shelves. I do like theidea of the Panda screens being a bit more flexible, so to speak, but the need for the area to be light proof is trumping all those type of ideas I've had, so far.

Your grow looks tasty. The software I used is Adobe Illustrator (expensive) but much cheaper graphics programs will do.
I second the Panda Plastic, I use it and it's lightproof and reuasable, you can clean it and it leaves you with a huge amount of flexibility, as you have already said. Good to see you are organized, you're grow is going to be nice.
 

Tags
possible, room, setup

Thread Tools
Display Modes

Thread

Thread Starter

Forum

Replies

Last Post

new setup grow room dog General Marijuana Growing 8 07-31-2007 01:21 PM
My new grow room setup boricuaboi Indoor Growing 6 06-22-2007 08:54 PM
grow room setup help hoc19e General Marijuana Growing 5 04-14-2007 12:19 PM
New Room so new setup needed spowage18 Indoor Growing 3 02-22-2007 09:37 AM
Grow Room Setup delta9thc General Marijuana Growing 6 11-28-2006 08:05 PM

Posting Rules

You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Come Check out a new Poker Forum for the online poker community

All times are GMT -7. The time now is 02:44 AM.
Powered by vBulletin
Copyright © 2000-2009 Jelsoft Enterprises Limited.

Content Relevant URLs by vBSEO 3.3.2