Hey all.

For those of you who have made DIY aero setups - The kind where the res is inside the aero tub itself making it a kind of aero combined with DWC system lol - have you had any troubles with leaks forming around the lid due to water spraying around the top of the tub, collecting between the top of the tubs sides and lid, and then dripping outside of the tub?

Hope that makes sense Can anyone give me some suggestions on how to fix this. Any suggestions welcome, but preferably from people with experience with this.

Cheers!

__________________

GreenX ~ Glossary of Terms:
http://www.rollitup.org/general-mari...ary-terms.html

no i havent had that problem, i do however know what you are talking about.


weatherstripping or gasket like lining.

__________________
da fuck?

wally world has these small individual packets of clear silicone sealant, you could try putting a nice thin line around the inside lip of the lid or the outside lip of the tub. I can't remember if there are any problems with using it with plastic but they were only like $2 so it couldn't hurt to try. Good Luck

Yea I didn't have this problem on my last aero setup, unfortunately when I build I bigger, better one this problem all of a sudden occurs lol ... Thanks for the suggestion, I'll look into that - Best way to attach it???

Any other suggestions still welcome

Cheers

__________________

GreenX ~ Glossary of Terms:
http://www.rollitup.org/general-mari...ary-terms.html

it has an adhesive backing

__________________
da fuck?

I'm not sure if you are talking to me or the post above but you squeeze the silicone out like wet caulking, i think they were called "One Caulk" or something, and sets dry to the touch in about 30 mins, and completely dry in a few hours. I bought a packet it wasn't hard to use but i don't have the packet anymore so i can only tell you what i remember.

Oh if i haven't been clear yet i'm suggesting adding a thin line of silicone all around the inside of the lid or the outside of the tub. Then let it dry on either and form a custom gasket seal that you create. I think logistically it makes more sense to put the thin line on the inside lip of the lid assuming that the tub is like a rubbermaide tub and has a rounded lip. The lid and sealant would have an easier time slipping over the rounded edges of the tub rather then the stiff edge of the lid trying to slip over the the rounded edge with the added width of the sealant... i'm just guessing though. You could probably just peel it off when its dry if it doesn't work as well.

Was talking to poster before you lol ... Your post wasn't there when I posted reply to first message ... Cheers for the suggestions, will look into that too mate!

__________________

GreenX ~ Glossary of Terms:
http://www.rollitup.org/general-mari...ary-terms.html

all these other suggestions aside, i have the same problem and the quickest cheapest solution. I had some plastic sheeting, like vapor barrier or paint drop cloth (even large garbage bags). Cut two equal rectangles out of it, both are about a foot wider then my res on all sides. Then cover the res lid with the plastic, tucking in all four sides under the lid so the plastic hangs inside the res for a few inches. Then, cut ur net pot holes out of the plastic with an exacto and replace ur plants. It has worked perfectly for me, and it was the all arround cheapest solution i could figure out.

__________________
My Journal- http://www.rollitup.org/grow-journal...c-cabinet.html
For Canada

i had this issue when i wasnt smart enough to make a hole for the powerline for the pump, then tried silicone, that didnt help, so i made the new hole on top for the line and peeled off the silicone and voila! no more leaks

__________________
SOL: It's the Russian. AVI:A Russian? SOL:To be technical hes Uzbekistanian?AVI:I been dealing with those Russian dogs. AVI:give me a name.SOL:Urinov,Boris TONY:BORIS the BLADE? as in BORIS THE BULLET DODGER?AVI:why do they call him the bullet dodger?TONY: bcus he dodges Bullets Avi

LOL - I almost made that mistake! - I made holes for the air lines going in and everything, was checking over the design and then thought, hmm, where's the cord for the water pump going to come out? lol, solved the problem before it was a problem! lol

That sounds like an ultra cheap solution ... Can you take some pics and post them? Your description was good, but just to double check everything. Cheers.

__________________

GreenX ~ Glossary of Terms:
http://www.rollitup.org/general-mari...ary-terms.html