Continuation from:

GHS NL#5 x Haze Mist 25 clone SOG

Greetings to all thats following my journal.

My new mother/cloning/1st stage veg room arrived today along with a replacement, more powerfull RUCK fan for my budbox flower room plus a new grasslin mechanical timer and a new 2kw contactor/relay to switch the veg room lights safely without the worry of frying the new timer or causing a fire.

Attached Images

HPIM0945.jpg (49.9 KB, 218 views)

The darkroom frame assembled and the cover fitted.

(Excuse the bare floorboards i ripped the old carpet up 2 days ago and im waiting for new flooring to be delivered)

Attached Images

	HPIM0946.JPG (32.4 KB, 147 views)
	HPIM0947.JPG (47.0 KB, 228 views)

The 250w hps fitted in cooltube and mounted to the top support bar of the darkroom, c/filter fitted in place (the darkroom came with two handy straps for supporting the c/filter) and all ducting fitted, and light fired up to make sure it still works fine as i havnt used it for a while.

Attached Images

	HPIM0949.jpg (58.8 KB, 216 views)
	HPIM0948.JPG (65.0 KB, 230 views)
	HPIM0956.JPG (43.1 KB, 178 views)

I removed the RVK 5" (240m3 p/h) extractor from the flower room and fitted it onto the output duct from the darkrooms cooltube/extraction/filtration setup in above pictures, to pull air out and draw LOADS of fresh air in via the DR's passive intakes, this fan is a bit over-rated for the size of the tent but it'l do, it sucks the sides of the tent in quite a bit

Attached Images

HPIM0957.JPG (28.8 KB, 105 views)

I knocked up a quick table out of some scraps of MDF i had on my balcony to seperate the two sections of the room, covered the top with some thick white blackout sheeting that i had spare.

Then hung the two 125w eco-lites on the undersides of the table to form the mother/cloning room.

Then of course i put my two NL5 Haze mist mums in along with the BB Cheese mum in their new home.

Attached Images

	HPIM0959.JPG (42.4 KB, 307 views)
	HPIM0966.JPG (55.6 KB, 461 views)
	HPIM0960.JPG (49.5 KB, 349 views)

Ok, so with the addition of an oscillating fan for air movement and a digital thermometer/hygrometer my new room is complete.

Attached Images

	HPIM0959.JPG (42.4 KB, 165 views)
	HPIM0964.JPG (42.1 KB, 108 views)

The 240m3 p/h 5" RVK fan that was being used in my budbox flower room is now being used to extract the new room so its been replaced with the new 365m3 p/h 5" RUCK fan, my flower room temps as a result have dropped by 2 degrees C, Bonus!

To mount the RUCK fan into the budbox, i screwed two eyehooks into two of the threaded mounts on the RUCK fan, attached two lengths of jack chain and wrapped the chain around the top support bar of the budbox, and attached the fan at the sucking end to the c/filter using a fast clamp, and the other blowing side of the fan attached to the duct which supplies the air cooled shade with cool air.

Attached Images

	HPIM0953.JPG (27.1 KB, 53 views)
	HPIM0954.jpg (29.7 KB, 48 views)
	HPIM0955.JPG (40.6 KB, 111 views)

Ok, by the time my current NL5 Haze mist flowering plants are 3wks or so from being finished in the budbox, the mothers should be a decent enough size to take plenty of clones from.

Il be taking 25 clones from the three mums and the clones will be rooted in a propagator in the same room and under the same lights as the mothers.

As usual il be using Growth technology organic root riot cubes for rooting the clones along with Growth technology Clonex gel as my rooting hormone.

Attached Images

	HPIM0966.JPG (55.6 KB, 215 views)
	HPIM0961.JPG (47.5 KB, 167 views)

nice litle op you got going, i see your using a budbox, are they worth the money? thinking of getting one soon as if they're decent.