You guys have been awesome the list is getting huge. Check it out and see if your invention is there. GrowFAQ, DIY and save, click on page 2 (it's that long we needed a second page!)

great job on getting that all together Mogie

__________________
There's Gonna Be Alot Of Slow Singin
And Flower Bringin
If My Burgular Alarm Starts Ringin

yeah that is a really good job, it was really helpful because i like do it yourself pipes and s and shit.

__________________
In Weed We Trust. Legalize Today. Weed was put on the Earth by God for Men so we could get HIGH.

I just put this beast together, hits like a champ
its a 1 litre bottle.
Sealed the stem opening with almost half a candle's worth of wax then some crap school glue (cooled with hair dryer) then put a cardboard ring around + tape for protection.

the slide is so you can easily dump and clean the bowl EVEN if you wasted, just as long as you dont dump the bong over.

the card is a little small for my likings but it works.


sorry the pictures are so big, had to use a digital camera because my webcam busted.


Whole Bong



Slide and Stem Housing



Slide (tape so it fits snuggly in the stem)




Carb, just because i can

Alright...I have a home made smoking device, I'm willing to fork it over, or get a photo of it, but i cant explain it, its way to complicated, but it hits like a champ, so what do you say people...?

Plus my home made smoking device looks like it was made by a professional...?

Materials
* 1 POM Pomegranate Juice drink(walmart,kroger,etc.)
* Razor or knife
* a bong slider and glide w/ rubber o-rings
* water(optional)

Procedure
Step 1: Drink POM and wash thoroughly with soap and hot water.
Step 2: Cut perfectly sized hole in side of bottom-most 'bubble' of bottle for the glide to
fit.
Step 3: Insert rubber o-ring to fit hole for slider glide, then fit glide into the new opening
Step 4: Fill above glide with water and insert slider and bake through the top. Enjoy!

Attached Images

IMG_0223[1].jpg (90.8 KB, 0 views)

__________________
GANJANATOR

Materials
* One 7 inch piece of 2 inch diameter PVC piping
* One 2 inch diameter PVC piping endcap
* Knife or drill w/ 1/8 inch bit

Procedure
Step 1: Seal endcap to piece of PVC, then clean with hot water,
Step 2: Cut or drill joint-sized hole into center of endcap.
Step 3: Then cut or drill tiny hole near the open end for carbeurator.
Step 4: Roll one up and fit it into the hole snug, hold carb, light and toke up!

Attached Images

IMG_0222[1].jpg (58.6 KB, 0 views)

__________________
GANJANATOR

Materials
* 2-3 same sized pill bottles
* Hot Glue Gun
* Bendy straws
* Knife
* Scissors
* a bowl n stem (preferrably metal)

Procedure
Step 1: Cut straw-sized holes into bottom-center of 2 pill bottles.
Step 2: Insert longer end of bendy straw in through the open end of each of the 2
bottles down through the holes in the bottoms. (must look like upside down U
inside bottle) Seal with hot glue and clip off excess straw from bottom.
Step 3: Fill the 2 'percolating' bottles halfway with water and fit bottom of one into the
top of the other tightly.
Step 4: Cut hole into bottom-center of last bottle and fit bottom of bottle into top of the
other 2 bottles.
Step 4: Cut hole into side of bottom-most bottle and fit stem and bowl in and seal.
Step 5: Cut tiny hole into side of top-most bottle for carbeurator.
Step 6: Let sit... pack bowl, light and toke!!!!

Attached Images

IMG_0220[1].jpg (118.1 KB, 0 views)

__________________
GANJANATOR

Materials:
* a Thermos that can fit almost a whole 2 liter( go find one somewhere...)
* an empty 2 liter( stripped of labels)
* Knife
* Glass slider w/ rubber o-ring

Procedure
Step 1: Clean Thermos and 2 liter and strip labels off.
Step 2: Cut bottom off of 2 liter.
Step 3: Cut hole into cap just big enough to fit stem of glass slider into.
Step 4: Pack bowl, keep lit and pull up, take cap off when ready and push down inhaling. boooooonnnnngggggg........

Attached Images

IMG_0217[1].jpg (36.2 KB, 0 views)

__________________
GANJANATOR