First ATTEMPT at WAX/BHO/BUDDER/ETC. wtf happened?

Fadedawg

Well-Known Member

Whats up guys, I recently bought a G pen because I love wax and its very convenient on the go. However, I refuse to pay 45-60 for a gram. So I decided to try and make some wax. Heres how it went..

Bought 1 ft. of copper tubing 1" wide. Copper Cap for one side. Brown (unbleached) coffee filters. and a hose clamp. I also bought Neon 5x Butane.
I used 1/2 oz of bud trim of some kush.

First I used tarn-x to get the tarnish off the copper tubing. (I read that you were supposed to do this when using a copper pipe)
After cleaning the pipe I put it all together and packed it full of the trim. packing it down slightly after every cup.
I used 2 coffee filters and clamped them down with the clamp.
Ran the full bottle of butane through the trim (300ml) and ended up with a sort of green/yellowish liquid.
I let the butane evaporate for a while without stirring or anything of that nature. (yes i did this outdoors!)
After I felt it was evaporated enough to go indoors I put it on my electric stove on low heat.you couldn't even really see anything, i figured it didn't work...

after a minute this stuff began to look like this-

BUT IT REEKED LIKE BUTANE. I let it bubble up and i'd mix it. Then, I let it air out overnight and the next morning it STILL smelled like butane. but I scraped it all together and ended up with this.

after it still smelling like butane i put it back on the heat. (the next day) and it looked like this.

still reeking of butane.. I didn't want to smoke it. every time i put it back on the heat the pile of whatever it is... gets smaller. it doesn't smell so much like butane now. But since it doesn't look like any wax i've ever smoked, i didn't want to smoke it. its consistency is like a corn syrup... any ideas as to what I did wrong? Anything is MUCH appreciated!

300 ml is too much butane for a half ounce of bud. Butane will absorb up to 32 ml/liter water and the electric green is a dead giveaway that you have extracted water solubles.

If you will set your collection dish in hot tap water while injecting, it will help keep atmospheric water out and speed up the process.

Once all the butane is visably gone sitting in hot tap water, you are ready for final purge, which won't happen anytime soon unless you add some heat or vacuum. 115F works well in conjunction with -29.5 vacuum, but without vacuum it is necessary to go to 140F or above, with the fastest purging above about 180F, where the cannabinoids are fully molten.

Passing air over it also speeds up the process, by keeping the enriched boundary layer removed. Here are a couple of links that cover extracting with BHO and purgeing residuals by various methods, starting with not imolating oneself. Also one explaining how chlorophyll may be picked up.

http://skunkpharmresearch.com/butane-safety/, and http://skunkpharmresearch.com/bho-extraction, plus http://skunkpharmresearch.com/chlorophyll-pickup-in-extractions/
 

biglungs

Active Member
haha I wasn't blaming you or anyone else, i don't care... honestly the debates are what sparks my interest anyways. What method do you use BigLungs? or do you have a thread?
glass tube with a rubber stopper silk screen and a coffee filter at the bottom hot water purge
 

Fadedawg

Well-Known Member
Stainless steel is the only metal you should use,and glass. Even pvc is better than copper.
We use borosilicate or stainless columns. Copper works fine, if it is oxide free. Welding copper without adequate fume protection, produces an occupational disease known as fume fever.

I wouldn't use PVC under any circumstances. It leaches out constituets into the butane, some of which are carcinogenic.
 

rollNfattys420

Well-Known Member
thats what i thought faded dog.. I just went to the HWS and told them i needed 1 ft x 1" copper pipe. I had read that you must take the tarnish off the inside, hence the tarnx, on the bottle it said known in cali to cause cancer, so i didn't smoke this batch.. im going to use the mason jar method that big lungs suggested..
 

Fadedawg

Well-Known Member
You can also pickup a stainless steel thermos at Goodwill for about $15, or a stainless steel basting syringe for $8 from Bed, Breakfast, and Beyond.
 
Top