I didn't get any replies as to how to get my post from yesterday in the running for the new contest so I'm just redoing it as this thread with the poll option added. If you like it give it a vote; if you really like it, give me a rep. BTW, I did add the name of the manifold I used if you don't have one.

I spent today building my NTF system. I had already gotten the idea, designed it, bought the stuff I needed before I saw that they actually sell ones almost exactly like this. Nonetheless, I made mine today. The only thing I am lacking is germinated seeds but I have seeds and more on the way. For those of you that are familiar with NTF (Nutrient Film Technique), you know the benefits of the system without the drawbacks of a regular hydro setup. I'm using 1/2 gal drippers, two on each net pot. The air pump is driving two 6" bubble stones and the water pump is rated at 396 GPH. I'll try and 'splain the pix as I go thru.

Buy a section of 5.5" PVC fence post at HD, 6 end caps, some vinyl glue and a section of 2.5" square PVC post. I bought a 3.25" hole saw because I would be doing 12 holes (for this one) and I wanted them nice and clean with no light leakage. Cut the fence post into 3 pieces; if they are 96", that will yield 32" pieces. Debur the cuts. I did a hole very near the end of each of the three "containers" as I'll call them. I spaced out the other 2 holes equally, a calculator and a tape measure comes in handy on this job. I put a cap on one end of each one.


I wasn't sure how I was going to get the water to run down and back into the res tank but after some thought, here is what I came up with. I cut a slot into the bottom of one end (allowing for the end cap).

You have to file and deburr every cut you make on the PVC; you don't want the crap plugging up your water pump.


I added a little Liquid Nails construction adhesive to make sure the water goes right into the return slot.


Using the little 2.5" post, I drilled holes to allow me to cut a matching slot (doesn't have to be perfect) in the bottom return tube.


Use the vinyl glue and glue the rest of the caps on then glue the containers to the return tube and a matching strut on the other end. The strut is the same but has no slots.


I drilled a couple of holes in the bottom of my return tube and cut a line between them. I then used a heat gun to soften the PVC and bend it so that it made flanges for the water to run down.


Get your res tank ready, the standard one everyone uses. I used black vinyl tubing and connectors, all found at HD in the plumbing section. I got my bubble stones hooked up and in place with the hose running out to the pump.


I had plenty of 2.5" post left so I used it to make two legs. You want the water to drain down by gravity so remember not to make it level. Clamps are handy for this but the vinyl glue sets pretty quickly if you don't use too much.


I made mine about half a bubble off from level; that should be plenty.


Rigging the hoses and drippers take the most time but it's just like putting a Lego set together. I ran out of hose clamp-downs (I will add them later) so I used some I-Screws that I had; they will work just as good. At this point you're pretty much done. The manifold is a real find at HD; it's a Rain Bird Drip Irrigation Retrofit Kit.


You'll notice that there is a little bit more space between two of the containers than between the other two; that's so I could mount my air pump and manifold between them as shown. Handy but out of the way.


Notice the end caps to the return tube? You don't want light getting to your water. I also scribed a piece of plastic to make a cover to make sure no light gets into the res tank. I'll add some black electrical tape just to make doubly sure.


The manifold is mounted in high tech fashion - with a small bungee.




Top View:


So there you have it boys and girls and if you have half as much fun building yours as I had building mine... that means that I had twice as much fun as you.

Peas and Love

__________________
http://www.rollitup.org/grow-journal...idow-grow.html

Hey Potpimp!
Lookin' very stylish! Just three thoughts:

1. Four independant legs would allow "easy access" to the reservoir.

2. "Spreader Mat" would help even the flow in the "container" troughs.

3. Have you considered root mass build-up? I think you may well have a blockage problem in those narrow slots between the container troughs and the return tubes. As the root sytems develope, they tend to want to hang down into the reservoir - potentially causing a blockage.

I plan on building a DIY-NFT System (some day - LOL!) and I think your's is da bomb! Let us know how it works out. And remember "You got's to keep your Pimphand strong!

this has got to be the best system DIY I've seen in a long time!

just wanted to know what type of watering schedules you use with this setup?

__________________
warning: may contain traces of nuts and dairy.

Hey T.H., thanks for the kind words. I started to put a couple of "swing-down" legs on it but decided against doing it for now just because it was late in the day. I think I'd use some aluminum angle or thin square tubing for that. The spreader mat is a great idea and would certainly enhance the system (Thank you!). I'll just have to wait and see about the root mass buildup; there *should* be plenty of room for water to flow thru; I can't see it totally blocking the flow but I'll certainly keep my eyes on it.

Another idea I had last night was, since I'm using a 396 GPH pump (I do have another one that's half that capacity) and the 24 drippers only drip 12 GPH, I'm thinking that there might be a lot of stress put on the pump due to the back pressure. I'm thinking about drilling a hole in the end of each container and tucking the tubing in it, allowing the rest of the water to flow down (True NFT), not just relying on the drippers. I've always said that good design is an evolutionary process. Thanks for the props!

__________________
http://www.rollitup.org/grow-journal...idow-grow.html

free bump
also, I think that your next growFAQ should be how to use this system, start to finish.

that would be a great addition to the faq, because I don't think there is anything like it in there, and a dummies 123 setup and grow tutorial would be great for newbies with an average budget. (although I could be wrong)

__________________
warning: may contain traces of nuts and dairy.

I've been expecting some Maui Waui seeds and some Vintage seeds (Accupulco Gold, Panama Red, Columbian Gold X White Widow) to grow in this system but they haven't come in yet. I got about 100 seeds (maybe 80 viable) out of the last bag I bought recently, probably Mexican but some good stuff, and I have more blueberry. I may just go ahead and germ more of the Blueberry today and plant them on Sunday. My grow closet is packed to the walls and I'm using 65w CFL's for the babies but they should be ready for the HID in a week or so. I need to figure out where I can keep another grow box if I do that.

__________________
http://www.rollitup.org/grow-journal...idow-grow.html

Help me out here, submit a material list and cost it out?? VV

My cost on everything was $170 including tax.

__________________
http://www.rollitup.org/grow-journal...idow-grow.html

Why such a large pump? Do you really need 396 gph?

I think you need to build up a good head of pressure to accuate the drippers that Potpimp is using - not sure just how much it takes, but something like normal water supply pressure. I'm sure someone will correct me if I'm wrong!

I think the thing that really caught my eye was Potpimp's use of net pots instead of the usual Rockwool cubes. It's not that they don't work well, but the Rockwool cubes just don't "look right", if you know what I mean. I think the net pots give an overall cleaner look to the whole system.

Can't wait to hear how this baby woks out!